Skip to content

IGCSE Physics · March 2022 · Paper 52 · Difficulty 3 · Standard

Question 2

2

In this experiment, you will investigate the thermal insulation properties of air.

Carry out the following instructions, referring to Fig. 2.1 and Fig. 2.2.

Beaker A is covered in thin black card.

Beaker A is used on its own for the first part of the investigation and is placed inside beaker B for the second part of the investigation.

(a)

Remove the lid from beaker A.

Pour $150\text{ cm}^3$ of hot water into beaker A and replace the lid.

Place the thermometer in the water.

In the first row of Table 2.1, record the temperature $\theta$ of the water at $t = 0$ and immediately start the stop-clock.

Record the temperature $\theta$ of the water at times $t = 30\text{ s}$, $t = 60\text{ s}$, $t = 90\text{ s}$, $t = 120\text{ s}$, $t = 150\text{ s}$ and $t = 180\text{ s}$.[1]

(b)

Remove the thermometer and lid from beaker A and pour away the water.

Place beaker A inside beaker B, as shown in Fig. 2.2, so that there is an air gap between the sides of the two beakers.

(i)

Repeat (a) for this arrangement, ensuring that the lid fits inside beaker B after pouring water into beaker A.[2]

(ii)

Add units to the column headings in Table 2.1.[1]

Table 2.1

beaker Abeaker A
inside beaker B
$t/$$\theta/$$\theta/$
0
30
60
90
120
150
180
(c)

Write a conclusion stating whether the air gap affects the rate of cooling of the water.

Justify your answer by reference to values from your results.[2]

(d)

A student suggests that glass is a thermal insulator and the experiment does not just test the effect of the air gap.

Suggest one change to the apparatus that would test the air gap more effectively.[1]

(e)

Another student repeats the experiment using the apparatus you used for your investigation.

State two variables that this student should control to obtain readings as close as possible to your readings.

[2]

(f)

Calculate the average cooling rate $R$ for beaker A cooling on its own. Use your readings for beaker A in Table 2.1 and the equation

$$R = \frac{\theta_0 - \theta_{180}}{T}$$

where $T = 180\text{ s}$ and $\theta_0$ and $\theta_{180}$ are the temperatures of the water in beaker A at $t = 0$ and $t = 180\text{ s}$.

Include the unit for the cooling rate.

$R =$ [2]

Show the mark scheme

These are the official mark-scheme rows. Each point that matches your answer earns a mark.

Tap the mark scheme to open it full size.

Show a worked answer

How to reach each mark, step by step. Try the question yourself first.

2(a)

  • Record the temperature at each time from $0$ to $180\,\mathrm{s}$. The readings should decrease as the water loses energy to the surroundings.

2(b)(i)

  • Record the temperature at each time to at least the nearest $1\,{}^\circ\mathrm{C}$. The readings should decrease as the water cools.
  • The temperature should fall more slowly than for beaker A alone, because the air gap reduces energy transfer.

2(b)(ii)

  • The time column needs $\mathbf{s}$; both temperature columns need $\mathbf{{}^{\circ}C}$.

2(c)

  • Compare the temperature falls over $180\,\mathrm{s}$ using your own readings. A smaller fall means a slower average cooling rate.
  • For example, if beaker A falls from $80$ to $68\,{}^\circ\mathrm{C}$ and the nested beaker from $80$ to $72\,{}^\circ\mathrm{C}$, the falls are $12$ and $8\,{}^\circ\mathrm{C}$. The air gap slows cooling.

2(d)

  • Use a metal outer beaker. Metal conducts heat well, so the outer wall adds less insulation.

2(e)

  • Keep the initial water temperature the same.
  • Keep the volume of water the same.

2(f)

  • Use $R = \dfrac{\theta_0-\theta_{180}}{T}$.
  • For example, with $\theta_0 = 80\,{}^\circ\mathrm{C}$ and $\theta_{180} = 68\,{}^\circ\mathrm{C}$, $R = \dfrac{(80-68)\,{}^\circ\mathrm{C}}{180\,\mathrm{s}} = \mathbf{0.067}\,{}^\circ\mathrm{C/s}$. Use your own readings.
Original question

Log in or create account

IGCSE, A-Level & AP