Skip to content

IGCSE Physics · March 2022 · Paper 52 · Difficulty 3 · Standard

Question 1

1

In this experiment, you will investigate the extension of a spring and use it to determine the weight of a metre rule.

The spring has been set up for you.

Carry out the following instructions.

(a)

Measure and record the unstretched length $l_0$ of the spring, as shown in Fig. 1.1.

$l_0$ = cm

Suspend the 1.0 N load from the spring, as shown in Fig. 1.2.

Measure and record the stretched length $l_S$ of the spring.

$l_S$ = cm[1]

(b)

Suspend the metre rule from the spring using the hook fixed at the 95.0 cm mark, as shown in Fig. 1.3.

Place the other end of the metre rule so that the 5.0 cm mark of the rule rests on the pivot. The metre rule must rest on the pivot at the 5.0 cm mark throughout the experiment.

Place the load W on the metre rule with its centre at a distance $d$ = 20.0 cm from the pivot.

Ensure that the metre rule is horizontal by adjusting the clamp that holds the spring.

Measure, and record in Table 1.1, the stretched length $l$ of the spring, as shown in Fig. 1.3.

Repeat this procedure for distances $d$ = 30.0 cm, $d$ = 40.0 cm, $d$ = 50.0 cm and $d$ = 60.0 cm from the pivot.

Table 1.1

d/ cml/ cm
20.0
30.0
40.0
50.0
60.0

[2]

(c)

Plot a graph of $l$/cm ($y$-axis) against $d$/cm ($x$-axis). Start the axes at the origin (0,0).

[4]

(d)
(i)

From your graph, determine $L$, the value of $l$ when $d$ = 0.0 cm.

$L$ = [1]

(ii)

Calculate $W_R$, the weight of the metre rule, using your value of $L$ from (d)(i), the values of $l_0$ and $l_S$ from (a) and the equation

$$W_R = \frac{2(L - l_0)}{(l_S - l_0)} \times k$$

where $k$ = 1.0 N.

$W_R$ = [1]

(e)
(i)

It is sometimes difficult to position the load W on the scale of the metre rule at the correct distance $d$ from the pivot.

Suggest one change to the apparatus to overcome this difficulty.

[1]

(ii)

Suggest one possible source of inaccuracy other than the difficulty described in (e)(i). Assume that the experiment is carried out carefully.

[1]

[Total: 11]

Show the mark scheme

These are the official mark-scheme rows. Each point that matches your answer earns a mark.

Tap the mark scheme to open it full size.

Show a worked answer

How to reach each mark, step by step. Try the question yourself first.

1(a)

  • Measure the spring itself without the load, then with the $1.0\,\mathrm{N}$ load. The loaded length $l_S$ should be greater than $l_0$.
  • For example, your readings might be $l_0 = \mathbf{4.0}\,\mathrm{cm}$ and $l_S = \mathbf{6.0}\,\mathrm{cm}$. Use your own measurements.

1(b)

  • Measure $l$ for each position of the load. Record each length to the nearest millimetre, or $0.1\,\mathrm{cm}$.
  • The five lengths should increase as $d$ increases, because the load has a larger turning effect about the pivot.

1(c)

  • Label the horizontal axis $d/\mathrm{cm}$ and the vertical axis $l/\mathrm{cm}$. Start both axes at zero. Choose scales that use at least half the grid.
  • Plot all five measured pairs to within half a small square, using small, precise crosses. Draw a thin straight line of best fit and extend it to the vertical axis.

1(d)(i)

  • Extend your best-fit line to $d = 0$. Read $L$ where the line crosses the vertical axis, using your graph scale.

1(d)(ii)

  • Use $W_R = \dfrac{2(L-l_0)}{l_S-l_0}\times k$.
  • For example, if $L = 5.5\,\mathrm{cm}$, $l_0 = 4.0\,\mathrm{cm}$ and $l_S = 6.0\,\mathrm{cm}$, then $W_R = \dfrac{2(5.5-4.0)\,\mathrm{cm}}{(6.0-4.0)\,\mathrm{cm}}\times 1.0\,\mathrm{N} = \mathbf{1.5}\,\mathrm{N}$. Use your own readings.

1(e)(i)

  • Suspend the load from a loop of thread around the rule. Place the thread on the required mark so the load does not hide the scale.

1(e)(ii)

  • The metre rule may be non-uniform, so its centre of mass may not be at its midpoint.
Original question

Log in or create account

IGCSE, A-Level & AP