Skip to content

IGCSE Physics · November 2024 · Paper 53 · Difficulty 3 · Standard

Question 2

2

In this experiment, you will determine the resistance of a resistor.

The circuit has been set up for you.

Refer to Fig. 2.1.

(a)

Attach the crocodile clip to a length $l = 100.0\text{ cm}$ of the resistance wire. Close the switch.

Measure the potential difference (p.d.) $V_0$ across the resistor for $l = 100.0\text{ cm}$.

$V_0 = \text{...................................................... V}$[1]

Open the switch.

(b)

Adjust the position of the crocodile clip on the resistance wire to a length $l = 20.0\text{ cm}$. Close the switch.

Measure and record, in Table 2.1, the value of the current $I$ in the circuit.

Measure and record, in Table 2.1, values of the current $I$ for $l = 30.0\text{ cm}$, $l = 40.0\text{ cm}$, $l = 50.0\text{ cm}$ and $l = 60.0\text{ cm}$.

Open the switch.

Table 2.1

$l/\text{ cm}$$I/\text{A}$
20.0
30.0
40.0
50.0
60.0

[2]

(c)

Plot a graph of $l/\text{cm}$ ($y$-axis) against $I/\text{A}$ ($x$-axis).

Draw a best-fit straight line. You do not need to start the axes at the origin (0,0).

[4]

(d)
(i)

Determine the gradient $G$ of the graph. Show clearly on the graph how you obtained the necessary information.

$G = \text{.........................................................}$[1]

(ii)

Calculate the resistance $R$ of the resistor.

Use your value of $V_0$ from (a) and the equation

$$R = \frac{G \times V_0}{100k}\text{ where } k = 1.0\text{ A}$$

$R = \text{...................................................... } \Omega$[1]

(e)

Suggest one practical reason why other students might not obtain the same result as you, even if they do the experiment carefully.[1]

(f)

The resistance wire can become very hot during this type of experiment.

Suggest one change to the apparatus that prevents this.[1]

[Total: 11]

Show the mark scheme

These are the official mark-scheme rows. Each point that matches your answer earns a mark.

Tap the mark scheme to open it full size.

Show a worked answer

How to reach each mark, step by step. Try the question yourself first.

2(a)

  • Read the voltmeter with the clip at $100.0\,\mathrm{cm}$ and record $V_0$ to at least one decimal place. A suitable reading is between $1.5\,\mathrm{V}$ and $3.5\,\mathrm{V}$.

2(b)

  • Record the current for each of the five wire lengths, using at least two decimal places in amperes.
  • The readings should increase as the length increases. Use your measured values for the graph.

2(c)

  • Label the horizontal axis $I/\mathrm{A}$ and the vertical axis $l/\mathrm{cm}$. Choose scales so the points occupy at least half the grid.
  • Plot all five points accurately to within half a small square, using small, precise crosses.
  • Draw a thin, well-judged straight line of best fit through the trend of the points.

2(d)(i)

  • Use $G = \Delta l/\Delta I$. Draw a large triangle on the best-fit line and mark the two points used.
  • Divide the change in $l$ by the change in $I$ to find the gradient from your graph.

2(d)(ii)

  • Use $R = GV_0/(100k)$, with $k = 1.0\,\mathrm{A}$.
  • Substitute your gradient and measured $V_0$, keeping their units. Give $R$ in $\mathrm{\Omega}$; a suitable result is from $4.0\,\mathrm{\Omega}$ to $10.0\,\mathrm{\Omega}$.

2(e)

  • The exact point where the crocodile clip touches the wire may be uncertain, changing the length in the circuit.

2(f)

  • Add a resistor in series to reduce the current and so reduce heating of the wire.
Original question

Log in or create account

IGCSE, A-Level & AP