Skip to content

IGCSE Physics · November 2022 · Paper 61 · Difficulty 3 · Standard

Question 2

2

A student investigates the resistance of a lamp. She uses the circuit shown in Fig. 2.1.

(a)

On Fig. 2.1, draw a voltmeter connected to measure the potential difference (p.d.) across the lamp.[1]

(b)

The student places a sliding contact S on the resistance wire CE as close as possible to point C.

She measures the potential difference $V_1$ across lamp L and the current $I_1$ in the circuit. The readings are shown in Fig. 2.2 and Fig. 2.3.

(i)

Record the readings shown in Fig. 2.2 and Fig. 2.3.

$V_1 =$ V

$I_1 =$ A
[2]

(ii)

Calculate the resistance $R_1$ of lamp L. Use the equation $R_1 = \frac{V_1}{I_1}$. Include the unit.

$R_1 =$ [1]

(c)

She places the sliding contact S on the resistance wire as close as possible to point D. Point D is at the mid-point of the resistance wire.

She measures the potential difference $V_2$ across lamp L.

$V_2 =$ 1.4 V

She measures the current $I_2$ in the circuit.

$I_2 =$ 0.24 A

Calculate the resistance $R_2$ of lamp L. Use the equation $R_2 = \frac{V_2}{I_2}$. Include the unit. Give your answer to a suitable number of significant figures for this experiment.

$R_2 =$ [1]

(d)

She places the sliding contact S on the resistance wire as close as possible to point E.

She measures the potential difference $V_3$ across lamp L.

$V_3 =$ 0.9 V

She measures the current $I_3$ in the circuit.

$I_3 =$ 0.18 A

Calculate the resistance $R_3$ of lamp L. Use the equation $R_3 = \frac{V_3}{I_3}$. Include the unit.

$R_3 =$ [1]

(e)

Complete the following statements, referring to your practical experience and the results.

  1. As the length of resistance wire included in the circuit is increased, the brightness of the lamp
  2. As the length of resistance wire included in the circuit is increased, the resistance of the lamp

[2]

(f)

A variable resistor can be used in this type of experiment in place of the resistance wire.

Draw a circuit diagram to show a variable resistor in place of the resistance wire. Include the ammeter and the voltmeter in your diagram.[3]

[Total: 11]

Show the mark scheme

These are the official mark-scheme rows. Each point that matches your answer earns a mark.

Tap the mark scheme to open it full size.

Show a worked answer

How to reach each mark, step by step. Try the question yourself first.

2(a)

  • Draw a voltmeter symbol, a circle with V inside, connected in parallel across the lamp.

2(b)(i)

  • Read the voltmeter as $V_1 = \mathbf{2.4}\,\mathrm{V}$ and the ammeter as $I_1 = \mathbf{0.32}\,\mathrm{A}$.

2(b)(ii)

  • Use $R_1 = V_1/I_1$.
  • $R_1 = 2.4\,\mathrm{V}/0.32\,\mathrm{A} = \mathbf{7.5}\,\Omega$.

2(c)

  • Use $R_2 = V_2/I_2$.
  • $R_2 = 1.4\,\mathrm{V}/0.24\,\mathrm{A} = \mathbf{5.8}\,\Omega$ to two significant figures.

2(d)

  • Use $R_3 = V_3/I_3$.
  • $R_3 = 0.9\,\mathrm{V}/0.18\,\mathrm{A} = \mathbf{5.0}\,\Omega$.

2(e)

  • The lamp brightness decreases as the length of wire increases.
  • The lamp resistance also decreases, as shown by the calculated values.

2(f)

  • Draw the power source, ammeter, lamp and variable resistor in one complete series loop.
  • Use a resistor symbol with a diagonal arrow for the variable resistor. Connect the voltmeter in parallel across the lamp.
Original question

Log in or create account

IGCSE, A-Level & AP