Skip to content

IGCSE Physics · November 2022 · Paper 51 · Difficulty 3 · Standard

Question 2

2

In this experiment, you will investigate the resistance of a lamp.

Carry out the following instructions, referring to Fig. 2.1.

Fig. 2.1
(a)

Place the sliding contact S on the resistance wire as close as possible to point C.

Close the switch.

(i)

Measure the current $I_1$ in the circuit.

$I_1$ = A[1]

(ii)

Measure the potential difference (p.d.) $V_1$ across lamp L. Open the switch.

$V_1$ = V[1]

(iii)

Calculate the resistance $R_1$ of lamp L. Use the equation $R_1 = \frac{V_1}{I_1}$. Include the unit.

$R_1$ = [1]

(b)

Place the sliding contact S on the resistance wire as close as possible to point D. Point D is at the mid-point of the resistance wire.

Close the switch.

  • Measure the current $I_2$ in the circuit.

$I_2$ = A

  • Measure the potential difference $V_2$ across lamp L.

$V_2$ = V

  • Open the switch.
  • Calculate the resistance $R_2$ of lamp L. Use the equation $R_2 = \frac{V_2}{I_2}$. Include the unit.

$R_2$ = [2]

(c)

Place the sliding contact S on the resistance wire as close as possible to point E.

Close the switch.

  • Measure the current $I_3$ in the circuit.

$I_3$ = A

  • Measure the potential difference $V_3$ across lamp L.

$V_3$ = V

  • Open the switch.
  • Calculate the resistance $R_3$ of lamp L. Use the equation $R_3 = \frac{V_3}{I_3}$. Include the unit.

Give your answer to a suitable number of significant figures for this experiment.

$R_3$ = [2]

(d)

Complete the following statements, referring to your observations and results.

  1. As the length of resistance wire included in the circuit is increased, the brightness of the lamp
  2. As the length of resistance wire included in the circuit is increased, the resistance of the lamp

[2]

(e)

A variable resistor can be used in this type of experiment in place of the resistance wire.

Draw a circuit diagram to show a variable resistor in place of the resistance wire. Include the ammeter and the voltmeter in your diagram.[2]

Show the mark scheme

These are the official mark-scheme rows. Each point that matches your answer earns a mark.

Tap the mark scheme to open it full size.

Show a worked answer

How to reach each mark, step by step. Try the question yourself first.

2(a)(i)

  • Put S as close to C as possible and close the switch. Read $I_1$ from the ammeter, with your eye directly in front of its scale to avoid parallax.
  • Record the reading in $\mathrm{A}$ to at least two decimal places. The diagram shows no meter scale, so a numerical reading must come from the apparatus.

2(a)(ii)

  • With S near C and the switch closed, read $V_1$ from the voltmeter across the lamp. Record it in $\mathrm{V}$ to at least one decimal place, then open the switch.
  • The diagram shows how to connect the voltmeter, but gives no meter scale. Use your measured reading; a numerical value cannot be read from this diagram.

2(a)(iii)

  • Use $R_1 = V_1/I_1$. For example, if $V_1 = 2.0\,\mathrm{V}$ and $I_1 = 0.40\,\mathrm{A}$, then $R_1 = (2.0\,\mathrm{V})/(0.40\,\mathrm{A}) = \mathbf{5.0}\,\mathrm{\Omega}$. Use your own readings.

2(b)

  • Record $I_2$ and $V_2$ with the contact at D, then open the switch.
  • Use $R_2 = V_2/I_2$. For example, $R_2 = (1.2\,\mathrm{V})/(0.30\,\mathrm{A}) = \mathbf{4.0}\,\mathrm{\Omega}$. Use your own readings; $R_2$ should be less than $R_1$.

2(c)

  • Record $I_3$ and $V_3$ with the contact at E, then open the switch.
  • Use $R_3 = V_3/I_3$. For example, $R_3 = (0.60\,\mathrm{V})/(0.20\,\mathrm{A}) = \mathbf{3.0}\,\mathrm{\Omega}$. Use your own readings; $R_3$ should be less than $R_2$.
  • Give the resistance to 2 or 3 significant figures, in ohms.

2(d)

  • The lamp brightness $\textbf{decreases}$ as more resistance wire is included, because the current decreases.
  • The lamp resistance $\textbf{decreases}$ because the filament becomes cooler.

2(e)

  • Draw the cell, switch, ammeter, lamp and variable resistor in series. Use a resistor symbol with a diagonal arrow for the variable resistor.
  • Connect the voltmeter in parallel across the lamp.
Original question

Log in or create account

IGCSE, A-Level & AP