Skip to content

IGCSE Physics · November 2022 · Paper 51 · Difficulty 3 · Standard

Question 1

1

In this experiment, you will investigate the period of a pendulum. Carry out the following instructions, referring to Fig. 1.1 and Fig. 1.2.

Fig. 1.1 Fig. 1.2

A pendulum has been set up for you as shown in Fig. 1.1.

(a)
(i)

Measure the distance $l$ between the bottom of the clamp supporting the pendulum and the centre of the pendulum bob.

$l$ = cm[1]

(ii)

Explain briefly how you measured to the centre of the pendulum bob as accurately as possible.[1]

(b)

Adjust the length of the pendulum until the distance $l$ = 50.0 cm.

Displace the bob slightly and release it so that it swings. Fig. 1.2 shows one complete oscillation of the pendulum.

Measure, and record in Table 1.1, the time $t$ for 20 complete oscillations.

Calculate, and record in Table 1.1, the period $T$ of the pendulum. The period is the time for one complete oscillation.

Calculate, and record in Table 1.1, the value of $T^2$.

Repeat the procedure using $l$ values of 60.0 cm, 70.0 cm, 80.0 cm and 90.0 cm.

Table 1.1

$l$/cm$t$/s$T$/s$T^2$/s$^2$
50.0
60.0
70.0
80.0
90.0

[4]

(c)

Plot a graph of $T^2$/s$^2$ ($y$-axis) against $l$/cm ($x$-axis). Start the $T^2$ axis at a convenient value close to the minimum value of $T^2$.

[4]

(d)

Explain briefly why timing 20 oscillations gives a more accurate result for the period $T$ than timing 1 oscillation.[1]

[Total: 11]

Show the mark scheme

These are the official mark-scheme rows. Each point that matches your answer earns a mark.

Tap the mark scheme to open it full size.

Show a worked answer

How to reach each mark, step by step. Try the question yourself first.

1(a)(i)

  • Use a ruler to measure vertically from the bottom of the clamp to the centre of the bob. Record $l$ in $\mathrm{cm}$ to the nearest $0.1\,\mathrm{cm}$.
  • Use the actual pendulum: the sketch has no scale, so it cannot give a numerical value for $l$.

1(a)(ii)

  • Hold a horizontal set square against the centre of the bob and read its height on the ruler.

1(b)

  • Measure the time $t$ for 20 oscillations at each length. The times should increase as the length increases.
  • Use $T = t/20$. For example, if $t = 28.0\,\mathrm{s}$, then $T = (28.0\,\mathrm{s})/20 = \mathbf{1.40}\,\mathrm{s}$.
  • Use $T^2 = T\times T$. For this example, $T^2 = (1.40\,\mathrm{s})^2 = \mathbf{1.96}\,\mathrm{s^2}$. Use consistent significant figures in the table.

1(c)

  • Label the horizontal axis $l/\mathrm{cm}$ and the vertical axis $T^2/\mathrm{s^2}$. Start the vertical scale close to your smallest $T^2$ value.
  • Choose suitable even scales and plot each point to within half a small square. Draw a thin, continuous best-fit line.

1(d)

  • The reaction time error is a smaller fraction of the time for 20 oscillations, so the period is more accurate.
Original question

Log in or create account

IGCSE, A-Level & AP