Skip to content

IGCSE Physics · November 2021 · Paper 53 · Difficulty 3 · Standard

Question 2

2

In this experiment, you will compare the resistances of two wires.

The circuit has been set up for you.

Carry out the following instructions, referring to Fig. 2.1.

(a)

Connect the crocodile clip to a length $l = 90.0\text{ cm}$ of resistance wire A.

Close the switch.

Measure, and record in Table 2.1, the value of potential difference (p.d.) $V$ and current $I$ for the wire.

Open the switch.

Calculate, and record in Table 2.1, the resistance $R$ of $90.0\text{ cm}$ of wire A.

Use your values of $V$ and $I$ and the equation

$$R = \frac{V}{I}.$$

[3]

Table 2.1

wire$l\text{ /cm}$$V\text{/}$$I\text{ /}$$R\text{/}$
A90.0
B90.0
A50.0
B50.0
(b)
(i)

Repeat step (a) for $l = 90.0\text{ cm}$ of wire B, $l = 50.0\text{ cm}$ of wire A and $l = 50.0\text{ cm}$ of wire B.[2]

(ii)

Complete the headings in Table 2.1.[1]

(c)
(i)

Calculate a value $P$ using your results from Table 2.1 and the equation

$$P = \frac{R\text{ for }90.0\text{ cm of wire A}}{R\text{ for }90.0\text{ cm of wire B}}.$$

$P = \text{..........................................................}$[1]

(ii)

Calculate a value $Q$ using your results from Table 2.1 and the equation

$$Q = \frac{R\text{ for }50.0\text{ cm of wire A}}{R\text{ for }50.0\text{ cm of wire B}}.$$

$Q = \text{..........................................................}$[1]

(iii)

A student suggests that the values of $P$ and $Q$ should be equal.

State whether your results support this suggestion. Justify your answer by reference to values from your results.

statement

justification [2]

(d)

Suggest one reason why students all doing this experiment carefully with the same apparatus may not obtain the same results.[1]

[Total: 11]

Show the mark scheme

These are the official mark-scheme rows. Each point that matches your answer earns a mark.

Tap the mark scheme to open it full size.

Show a worked answer

How to reach each mark, step by step. Try the question yourself first.

2(a)

  • Close the switch and read the voltmeter and ammeter. Record $V$ to at least one decimal place and $I$ to at least two decimal places; then open the switch.
  • Use $R=V/I$. For example, with $V=1.2\,\mathrm{V}$ and $I=0.20\,\mathrm{A}$, $R=(1.2\,\mathrm{V})/(0.20\,\mathrm{A})=\mathbf{6.0}\,\mathrm{\Omega}$. Use your own readings.

2(b)(i)

  • For each of the three remaining wires and lengths, measure $V$ and $I$, then use $R=V/I$. Record each resistance to two or three significant figures.
  • For example, with $V=1.2\,\mathrm{V}$ and $I=0.40\,\mathrm{A}$ for wire B at $90.0\,\mathrm{cm}$, $R=(1.2\,\mathrm{V})/(0.40\,\mathrm{A})=\mathbf{3.0}\,\mathrm{\Omega}$. Use your own readings.

2(b)(ii)

  • The headings are $V / \mathrm{V}$, $I / \mathrm{A}$ and $R / \Omega$: potential difference is in volts, current in amperes and resistance in ohms.

2(c)(i)

  • Use $P=R_{A,90}/R_{B,90}$, where both resistances are for $90.0\,\mathrm{cm}$ of wire.
  • For example, if $R_{A,90}=6.0\,\mathrm{\Omega}$ and $R_{B,90}=3.0\,\mathrm{\Omega}$, then $P=(6.0\,\mathrm{\Omega})/(3.0\,\mathrm{\Omega})=\mathbf{2.0}$. Use your own results.

2(c)(ii)

  • Use $Q=R_{A,50}/R_{B,50}$, where both resistances are for $50.0\,\mathrm{cm}$ of wire.
  • For example, if $R_{A,50}=3.33\,\mathrm{\Omega}$ and $R_{B,50}=1.67\,\mathrm{\Omega}$, then $Q=(3.33\,\mathrm{\Omega})/(1.67\,\mathrm{\Omega})=\mathbf{1.99}$. Use your own results.

2(c)(iii)

  • Compare your calculated values of $P$ and $Q$. For example, $P=2.0$ and $Q=1.99$ support the suggestion.
  • These values are close enough for the small difference to be due to measurement uncertainty. Use your own results to decide whether they agree.

2(d)

  • The crocodile clip may not connect at exactly the same length each time, changing the length of wire in the circuit.
Original question

Log in or create account

IGCSE, A-Level & AP