Skip to content

IGCSE Physics · November 2021 · Paper 53 · Difficulty 3 · Standard

Question 3

3

In this experiment, you will investigate the image produced by a converging lens.

Carry out the following instructions, referring to Fig. 3.1.

(a)

Measure and record the height $h_O$ of the triangular object.

$h_O$ = cm

  • Place the lens a distance $u = 20.0\text{cm}$ from the triangular object.
  • Place the screen close to the lens.
  • Switch on the lamp.
  • Move the screen away from the lens until a clear, focused image of the triangular object is seen on the screen.
  • Measure, and record in Table 3.1, the height $h_I$ of the image.

Repeat the procedure for $u = 25.0\text{cm}$, $u = 30.0\text{cm}$, $u = 35.0\text{cm}$ and $u = 40.0\text{cm}$.[1]

Switch off the lamp.

Table 3.1

u/cmhI/cm1/hI / 1/cm
20.0
25.0
30.0
35.0
40.0
(b)

For each distance $u$, calculate, and record in Table 3.1, the value of $\frac{1}{h_I}$.[1]

(c)

Plot a graph of $u/\text{cm}$ ($y$-axis) against $\frac{1}{h_I} / \frac{1}{\text{cm}}$ ($x$-axis). Start the axes at the origin (0,0).

[4]

(d)
(i)

From your graph, determine $u_0$, the value of $u$ when $\frac{1}{h_I} = 0.0$.

$u_0$ = [1]

(ii)

Determine the gradient of the graph.

Show clearly on the graph how you obtained the necessary information.

gradient = [1]

(iii)

Calculate the focal length $f$ of the lens. Use your value of $h_O$ from (a) and the equation

$f = \frac{G}{h_O}$

where $G$ is numerically equal to the gradient from (d)(ii).[1]

$f$ =

(e)

Describe one difficulty that can be experienced when measuring the height of the image.

Suggest an improvement to overcome this difficulty.

difficulty

improvement [2]

[Total: 11]

Show the mark scheme

These are the official mark-scheme rows. Each point that matches your answer earns a mark.

Tap the mark scheme to open it full size.

Show a worked answer

How to reach each mark, step by step. Try the question yourself first.

3(a)

  • Measure the height of the triangular object, then focus the image and measure its height for each distance $u$.
  • For example, $h_{\mathrm{O}}$ could be $\mathbf{2.0}\,\mathrm{cm}$ and the image heights could be $6.0, 3.0, 2.0, 1.5, 1.2\,\mathrm{cm}$ in table order. They decrease as $u$ increases; use your own readings.

3(b)

  • Use $1/h_{\mathrm{I}}$ for each image height. Dividing one by the height gives its reciprocal.
  • For example, if $h_{\mathrm{I}}=2.0\,\mathrm{cm}$, then $1/h_{\mathrm{I}}=1/(2.0\,\mathrm{cm})=\mathbf{0.50}\,\mathrm{1/cm}$. Repeat for your own heights.

3(c)

  • Label the horizontal axis $1/h_{\mathrm{I}}\,/\,(1/\mathrm{cm})$ and the vertical axis $u/\mathrm{cm}$. Start both axes at zero.
  • Choose scales so the points fill at least half the grid. Plot each point within half a small square of its correct position.
  • Draw a thin, well-judged best-fit line through the trend of the points.

3(d)(i)

  • Find where the best-fit line meets the $u$-axis: there $1/h_{\mathrm{I}}=0$.
  • For example, if the line crosses at $15.0\,\mathrm{cm}$, then $u_0=\mathbf{15.0}\,\mathrm{cm}$. Read the value from your own graph.

3(d)(ii)

  • Draw a large gradient triangle on the best-fit line. Use $\text{gradient}=\Delta u/\Delta(1/h_{\mathrm{I}})$, taking both points from the line.
  • For example, if $\Delta u=15.0\,\mathrm{cm}$ and $\Delta(1/h_{\mathrm{I}})=0.50\,\mathrm{1/cm}$, the gradient is $(15.0\,\mathrm{cm})/(0.50\,\mathrm{1/cm})=\mathbf{30}\,\mathrm{cm^2}$. Use your graph.

3(d)(iii)

  • Use $f=G/h_{\mathrm{O}}$, where $G$ is the numerical value of your gradient.
  • For example, if $G=30\,\mathrm{cm^2}$ and $h_{\mathrm{O}}=2.0\,\mathrm{cm}$, then $f=(30\,\mathrm{cm^2})/(2.0\,\mathrm{cm})=\mathbf{15}\,\mathrm{cm}$. Use your own values.

3(e)

  • The ruler may block the light when measuring the image height.
  • Use a translucent screen and measure the image from behind it, so the ruler does not block the light.
Original question

Log in or create account

IGCSE, A-Level & AP