Skip to content

IGCSE Physics · November 2021 · Paper 52 · Difficulty 3 · Standard

Question 2

2

In this experiment, you will investigate the resistances of a resistor and a lamp.

Fig. 2.1 shows the first circuit arrangement. The circuit has been set up for you.

(a)

Switch on.

(i)

Record $V_S$, the potential difference (p.d.) across resistor R.

$V_S$ = [1]

(ii)

Record $I_S$, the current in the circuit and then switch off the power supply.

$I_S$ = [1]

(iii)

Calculate $R_S$, the resistance of resistor R, using the equation $R_S = \frac{V_S}{I_S}$.

$R_S$ = [1]

(b)

• Disconnect the voltmeter.

  • Replace the resistor with the lamp.
  • Connect the voltmeter across the lamp.
  • Switch on.
(i)

Record $V_L$, the potential difference across the lamp.

$V_L$ =

Record $I_L$, the current in the circuit and then switch off the power supply.

$I_L$ = [1]

(ii)

Calculate $R_L$, the resistance of the lamp, using the equation $R_L = \frac{V_L}{I_L}$.

$R_L$ = [1]

(c)

• Disconnect the voltmeter.

  • Connect the resistor R in series with the lamp.
  • Connect the voltmeter to record $V_C$, the potential difference across the series combination of the resistor and the lamp.
(i)

Draw the circuit diagram for this arrangement.[2]

(ii)

Switch on. Record $V_C$, the potential difference across the resistor and the lamp in series.

$V_C$ =

Record $I_C$, the current in the circuit and then switch off the power supply.

$I_C$ = [1]

(iii)

Calculate $R_C$, the combined resistance of the resistor and the lamp connected in series, using the equation $R_C = \frac{V_C}{I_C}$.

$R_C$ = [1]

(d)

State and explain briefly whether your results show that $R_S + R_L = R_C$ within the limits of experimental accuracy.

statement

explanation

[2]

Show the mark scheme

These are the official mark-scheme rows. Each point that matches your answer earns a mark.

Tap the mark scheme to open it full size.

Show a worked answer

How to reach each mark, step by step. Try the question yourself first.

2(a)(i)

  • Read the voltmeter across $R$ and record $V_{\mathrm S}$ in $\mathrm V$ to at least one decimal place. The reading depends on the circuit.

2(a)(ii)

  • Read the ammeter and record $I_{\mathrm S}$ in $\mathrm A$ to at least two decimal places. Then switch off the power supply.

2(a)(iii)

  • Use $R_{\mathrm S} = V_{\mathrm S}/I_{\mathrm S}$. Divide your voltage in $\mathrm V$ by your current in $\mathrm A$ to get $R_{\mathrm S} = \mathbf{V_{\mathrm S}/I_{\mathrm S}}\,\mathrm{\Omega}$ using their numerical values.

2(b)(i)

  • Read the voltmeter across the lamp for $V_{\mathrm L}$ in $\mathrm V$, and the ammeter for $I_{\mathrm L}$ in $\mathrm A$. Then switch off the power supply.

2(b)(ii)

  • Use $R_{\mathrm L} = V_{\mathrm L}/I_{\mathrm L}$. Divide your voltage in $\mathrm V$ by your current in $\mathrm A$.
  • Give $R_{\mathrm L} = \mathbf{V_{\mathrm L}/I_{\mathrm L}}\,\mathrm{\Omega}$ to 2 or 3 significant figures, using the numerical readings.

2(c)(i)

  • Draw the resistor and lamp in series with the power supply and ammeter, using the correct circuit symbols.
  • Connect the voltmeter in parallel across the resistor and lamp together.

2(c)(ii)

  • Read $V_{\mathrm C}$ from the voltmeter in $\mathrm V$ and $I_{\mathrm C}$ from the ammeter in $\mathrm A$. The series current should be less than each separate current.
  • Switch off the power supply after taking the readings.

2(c)(iii)

  • Use $R_{\mathrm C} = V_{\mathrm C}/I_{\mathrm C}$. Divide your voltage in $\mathrm V$ by your current in $\mathrm A$ to get $R_{\mathrm C} = \mathbf{V_{\mathrm C}/I_{\mathrm C}}\,\mathrm{\Omega}$ using their numerical values.

2(d)

  • Compare $R_{\mathrm S} + R_{\mathrm L}$ with $R_{\mathrm C}$. Answer yes if they agree within experimental accuracy, or no if they do not.
  • Support your answer with the difference between your values. A difference greater than about $10\%$ suggests they do not agree within experimental accuracy.
Original question

Log in or create account

IGCSE, A-Level & AP