Skip to content

IGCSE Physics · November 2021 · Paper 52 · Difficulty 3 · Standard

Question 1

1

In this experiment, you will determine the density of a block of wood.

(a)
(i)

Measure the length $l$, width $w$ and height $h$ of the block of wood.

$l$ = cm

$w$ = cm

$h$ = cm[1]

(ii)

Calculate the volume $V$ of the block of wood using the equation $V = l \times w \times h$.

$V$ = cm$^{3}$[1]

(iii)

Measure the mass $m$ of the block of wood using the balance provided.

$m$ = g[1]

(iv)

Calculate the density $\rho$ of the wood using the equation $\rho = \frac{m}{V}$. Give your answer to a suitable number of significant figures for this experiment and include the unit.

$\rho$ = [2]

(b)

Place the block of wood, largest face down, carefully in the water in the container.

(i)

Estimate, without taking a measurement, the volume $V_{1}$ of wood that is below the water surface.

$V_{1}$ = cm$^{3}$[1]

(ii)

Calculate $m_{W}$, the mass of water with volume $V_{1}$, using the equation $m_{W} = \rho_{W} \times V_{1}$, where $\rho_{W} = 1.00$ in the same units as $\rho$ in part (a)(iv).

$m_{W}$ = [1]

(c)

A student suggests that the mass $m$ of the block of wood is equal to the mass $m_{W}$ of the water with volume $V_{1}$.

(i)

Calculate the difference $d$ between your values of $m$ and $m_{W}$.

$d$ = [1]

(ii)

Discuss whether the difference $d$ is small enough to conclude that $m = m_{W}$.

[1]

(d)

Another student wants to obtain a more accurate value for $V_{1}$. He uses the method of floating the block of wood in water as described in (b).

Suggest how the student could obtain a more accurate value by taking a measurement.

You are not required to do this part of the experiment.

[2]

[Total: 11]

Show the mark scheme

These are the official mark-scheme rows. Each point that matches your answer earns a mark.

Tap the mark scheme to open it full size.

Show a worked answer

How to reach each mark, step by step. Try the question yourself first.

1(a)(i)

  • Use a ruler to measure the length $l$, width $w$ and height $h$. Record each reading in $\mathrm{cm}$.

1(a)(ii)

  • Use $V = lwh$. Multiply your three measurements in $\mathrm{cm}$ to get $V = \mathbf{lwh}\,\mathrm{cm^3}$ when their numerical values are used.

1(a)(iii)

  • Place the block on the balance and record its mass $m$ in $\mathrm{g}$. The reading depends on the block used.

1(a)(iv)

  • Use $\rho = m/V$: divide your mass in $\mathrm{g}$ by your volume in $\mathrm{cm^3}$.
  • Give $\rho = \mathbf{m/V}\,\mathrm{g/cm^3}$ to 2 or 3 significant figures, using the numerical values of $m$ and $V$.

1(b)(i)

  • Estimate what fraction of the block is below the water, then multiply that fraction by $V$. Round your estimate to the nearest $\mathrm{cm^3}$.
  • The estimate depends on the block: it should be at least half of $V$ but less than $V$.

1(b)(ii)

  • Use $m_{\mathrm W} = \rho_{\mathrm W}V_1$. With $\rho_{\mathrm W} = 1.00\,\mathrm{g/cm^3}$, the mass in $\mathrm{g}$ has the same numerical value as $V_1$ in $\mathrm{cm^3}$.
  • Using the numerical value of $V_1$, $m_{\mathrm W} = \mathbf{1.00V_1}\,\mathrm{g}$.

1(c)(i)

  • Use $d = m - m_{\mathrm W}$. Subtract your water mass from your block mass, both in $\mathrm{g}$: $d = \mathbf{m-m_{\mathrm W}}\,\mathrm{g}$ using their numerical values.

1(c)(ii)

  • Compare the size of $d$ with $m$ or $m_{\mathrm W}$. If it is small compared with the mass, answer yes; if it is too large, answer no.

1(d)

  • Float the block and mark the water level on its side.
  • Measure the submerged depth and multiply it by the area of the bottom face to find $V_1$.
Original question

Log in or create account

IGCSE, A-Level & AP