Skip to content

IGCSE Physics · June 2023 · Paper 53 · Difficulty 3 · Standard

Question 2

2

In this experiment, you will investigate circuits containing different combinations of resistors. Fig. 2.1 shows circuit A which has been set up for you.

Carry out the following instructions, referring to Fig. 2.1.

(a)

Circuit A

Close the switch.

Measure, and record in Table 2.1, the potential difference (p.d.) $V$ across resistor U.

Measure, and record in Table 2.1, the current $I$ in the circuit.

Open the switch.

Table 2.1

circuit$V / \text{V}$$I / \text{A}$$R / \Omega$
A
B
C

[1]

(b)

Circuit B

Connect a second $3\,\Omega$ resistor between terminals P and Q so that it is in parallel with the first $3\,\Omega$ resistor, as shown in Fig. 2.2. The rest of the circuit must remain as in Fig. 2.1.

Close the switch.

Measure, and record in Table 2.1, the potential difference (p.d.) $V$ across resistor U.

Measure, and record in Table 2.1, the current $I$ in the circuit.

Open the switch.[1]

(c)

Circuit C

Connect a third $3\,\Omega$ resistor between terminals P and Q so that it is in parallel with the other $3\,\Omega$ resistors, as shown in Fig. 2.3. The rest of the circuit must remain as in Fig. 2.1.

Fig. 2.3

Close the switch.

Measure, and record in Table 2.1, the potential difference (p.d.) $V$ across resistor U.

Measure, and record in Table 2.1, the current $I$ in the circuit.

Open the switch.[1]

(d)
(i)

Calculate, and record in Table 2.1, the resistance $R$ of resistor U for each combination of resistors. Use your readings from Table 2.1 and the equation $R = \frac{V}{I}$.[3]

(ii)

A student suggests that the values of $R$ should be the same.

State whether your results support this suggestion. Justify your statement by reference to values from your results.

statement

justification [2]

(e)

A student determines the resistance of resistor U using a variable resistor to control the current in the circuit.

(i)

Briefly explain one advantage of using a variable resistor for this purpose rather than the procedure carried out in (a), (b) and (c).[1]

(ii)

Draw the circuit symbol for a variable resistor.[1]

(f)

Another student suggests that potential difference and current for resistor U are proportional.

State how a graph of potential difference against current for resistor U can confirm this suggestion.[1]

[Total: 11]

Show the mark scheme

These are the official mark-scheme rows. Each point that matches your answer earns a mark.

Tap the mark scheme to open it full size.

Show a worked answer

How to reach each mark, step by step. Try the question yourself first.

2(a)

  • Close the switch and record the voltmeter reading across U and the ammeter reading in the circuit. Open the switch afterwards.
  • Your readings depend on the apparatus. The voltages should increase from A to C and each should be below $4.00\,\mathrm{V}$.

2(b)

  • Connect the second $3\,\mathrm{\Omega}$ resistor across P and Q, in parallel with the first. Record $V$ and $I$ with the switch closed, then open it.
  • The currents should increase from A to C and each should be below $1.00\,\mathrm{A}$.

2(c)

  • Connect the third $3\,\mathrm{\Omega}$ resistor across P and Q, in parallel with the other two. Close the switch, record $V$ and $I$, then open it.
  • Record all voltages to at least one decimal place and all currents to at least two decimal places.

2(d)(i)

  • Use $R = V/I$ for each circuit. Divide each measured voltage in V by its matching current in A to find $R$ in $\mathrm{\Omega}$.
  • Give all three results to the same number of significant figures, either two or three. The results should be within $10\%$ of each other.

2(d)(ii)

  • Compare your three values of $R$. If they agree within experimental uncertainty, say the results support the suggestion; otherwise, say they do not.
  • Quote the values from your table to show how close they are. Small differences can be due to measurement uncertainty.

2(e)(i)

  • A variable resistor lets you change the current smoothly and obtain more readings easily.

2(e)(ii)

  • Draw the resistor symbol as a rectangle with a diagonal arrow through it.

2(f)

  • A straight line through the origin shows that potential difference is proportional to current.
Original question

Log in or create account

IGCSE, A-Level & AP