Skip to content

IGCSE Physics · June 2023 · Paper 53 · Difficulty 3 · Standard

Question 1

1

In this experiment, you will determine the mass $M_{\text{R}}$ of a metre ruler using a balancing method.

Carry out the following instructions, referring to Fig. 1.1.

(a)
(i)

Place a load of mass $M = 20\text{ g}$ with its centre at the $5.0\text{ cm}$ mark of the metre ruler.

Explain briefly how you make sure that the centre of the load is at the $5.0\text{ cm}$ mark.

You may draw a diagram if it helps your explanation.[1]

(ii)

Place the metre ruler on the pivot. Adjust the position of the metre ruler on the pivot until the metre ruler is as near as possible to being balanced. Check that the position of the centre of the load remains at the $5.0\text{ cm}$ mark.

Record, in Table 1.1, the scale reading $p$ on the ruler at the position of the pivot.

Calculate, and record in Table 1.1:

  • The distance $a$ between the $5.0\text{ cm}$ mark and the pivot. Use your value of $p$ and the equation $a = p - 5.0$.
  • The distance $b$ between the $50.0\text{ cm}$ mark and the pivot. Use your value of $p$ and the equation $b = 50.0 - p$.

Repeat this procedure for values of $M = 40\text{ g}$, $60\text{ g}$, $80\text{ g}$ and $100\text{ g}$.[2]

Table 1.1

$M/\text{g}$$p/\text{cm}$$a/\text{cm}$$b/\text{cm}$$\frac{b}{a}$
20
40
60
80
100
(b)

For each value of $M$, calculate and record in Table 1.1 the value $\frac{b}{a}$.[1]

(c)

Plot a graph of $M/\text{g}$ ($y$-axis) against $\frac{b}{a}$ ($x$-axis).

Draw the best-fit line.[4]

(d)
(i)

Determine the gradient $G$ of the graph. Show clearly on the graph how you obtained the necessary information.

$G =$ [1]

(ii)

The mass $M_{\text{R}}$ of the metre ruler is numerically equal to $G$.

Write down the value of $M_{\text{R}}$ in this experiment. Include the unit.

$M_{\text{R}} =$ [1]

(e)

The determination of $M_{\text{R}}$ by this method assumes that the centre of mass of the metre ruler is at the $50.0\text{ cm}$ mark.

A student finds that the centre of mass of his metre ruler is at the $48.7\text{ cm}$ mark.

Suggest how he changes the procedure in (a)(ii) to allow for this.[1]

[Total: 11]

Show the mark scheme

These are the official mark-scheme rows. Each point that matches your answer earns a mark.

Tap the mark scheme to open it full size.

Show a worked answer

How to reach each mark, step by step. Try the question yourself first.

1(a)(i)

  • Read the ruler at both edges of the load. Adjust the load until the average of the two readings is $5.0\,\mathrm{cm}$.

1(a)(ii)

  • For each load, balance the ruler and read $p$ at the pivot. The five readings should be below $50.0\,\mathrm{cm}$ and decrease as $M$ increases.
  • Use $a = p - 5.0\,\mathrm{cm}$ and $b = 50.0\,\mathrm{cm} - p$. Check that $a+b = 45.0\,\mathrm{cm}$ for each row.

1(b)

  • For each row, divide $b$ by $a$ and record $\frac{b}{a}$ to at least two decimal places. The ratio has no unit because both distances are in cm.

1(c)

  • Label the horizontal axis $b/a$ and the vertical axis $M/\mathrm{g}$. Choose scales so the points spread over at least half the grid.
  • Plot each pair to within half a small square, then draw a thin, well-judged best-fit line.

1(d)(i)

  • Draw a large triangle on the best-fit line. Use $G = \frac{\text{change in }M/\mathrm{g}}{\text{change in }b/a}$, taking both changes from the triangle.
  • Your value of $G$ depends on your measurements and line.

1(d)(ii)

  • Use $M_R = G\,\mathrm{g}$. Read $G$ from your graph; the expected mass is between $\mathbf{100}$ and $\mathbf{200}\,\mathrm{g}$.

1(e)

  • Measure $p$ in cm and use $b = 48.7 - p$ to find the distance from the pivot to the actual centre of mass.
Original question

Log in or create account

IGCSE, A-Level & AP