Skip to content

IGCSE Physics · June 2023 · Paper 53 · Difficulty 3 · Standard

Question 3

3

In this experiment, you will investigate the reflection of light by two mirrors.

Carry out the following instructions, using the separate ray-trace sheet provided.

You may refer to Fig. 3.1 for guidance.

Fig. 3.1
(a)

• Mark and label a point F approximately in the centre of your ray-trace sheet.

  • Draw a 5 cm long line FV, from point F, as shown in Fig. 3.1.
  • Draw two lines, FG and FE, each 9 cm long and at 50° either side of FV, as shown in Fig. 3.1.
  • Draw a normal to line FG, crossing FG at a point N, 6 cm from F.
  • Label the lower end of the normal with the letter L.
  • Draw a line NA, as shown in Fig. 3.1, 8 cm long and at an angle $\theta_1 = 15^\circ$ to NG. [2]

(b)

• Place the plane mirrors on lines FG and FE, with their reflecting surfaces facing inwards, as shown in Fig. 3.1.

  • Place two pins, $\text{P}_1$ and $\text{P}_2$, on line NA, a suitable distance apart for accurate ray tracing.
  • Label the positions of $\text{P}_1$ and $\text{P}_2$.
  • View the images of $\text{P}_1$ and $\text{P}_2$ from the direction indicated by the eye in Fig. 3.1.
  • Place two pins, $\text{P}_3$ and $\text{P}_4$, a suitable distance apart, so that pins $\text{P}_3$ and $\text{P}_4$, and the images of $\text{P}_1$ and $\text{P}_2$, all appear one behind the other.
  • Label the positions of $\text{P}_3$ and $\text{P}_4$.
  • Remove the mirrors and pins from the ray-trace sheet. [1]

(c)

• Draw a line joining $\text{P}_3$ and $\text{P}_4$. Extend this line 10 cm above FE.

  • Label the lower end of this line with the letter B. Label the upper end with the letter R. [1]

(d)
(i)

• Draw a new line NA, 8 cm long and at an angle $\theta_2 = 40^\circ$.

  • Repeat the steps in (b).
  • Draw a line joining the new positions of $\text{P}_3$ and $\text{P}_4$. Extend this line until it crosses BR.
  • Label the lower end of this line with the letter C. Label the upper end with the letter T. [2]

(ii)

Measure the acute angle $\alpha$ between lines BR and CT. (An acute angle is less than 90°.)

$\alpha =$ $^{\circ}$[1]

(iii)

A student thinks that there is a relationship between angle $\alpha$ and the values of angle $\theta_1$ from (a) and angle $\theta_2$ from (d)(i).

State what your results suggest that relationship could be. Justify your answer by reference to values from your results.

statement

justification [2]

(e)

Suggest one precaution to take in this type of experiment to ensure accurate results.[1]

(f)

Suggest one reason why different students, all doing this experiment carefully, may not obtain identical results.[1]

[Total: 11]

Tie your ray-trace sheet into this booklet between pages 8 and 9.

Show the mark scheme

These are the official mark-scheme rows. Each point that matches your answer earns a mark.

Tap the mark scheme to open it full size.

Show a worked answer

How to reach each mark, step by step. Try the question yourself first.

3(a)

  • Draw the normal at $90^\circ$ to FG through N, which is $6\,\mathrm{cm}$ from F.
  • Draw NA at $15^\circ$ to NG, with NA $8\,\mathrm{cm}$ long.

3(b)

  • Place the pins in each pair well apart so that their alignment can be judged more accurately.

3(c)

  • Join $P_3$ and $P_4$ with a straight line and extend it to $10\,\mathrm{cm}$ above $FE$.
  • Label the lower end $B$ and the upper end $R$. Keep the first pin positions and ray lines visible.

3(d)(i)

  • Draw a new $NA$ of length $8\,\mathrm{cm}$ at $40^\circ$ to $NG$. Repeat the pin procedure and mark the new pin positions.
  • Join the new $P_3$ and $P_4$ positions and extend the line until it crosses $BR$. Label its lower end $C$ and its upper end $T$.

3(d)(ii)

  • Measure the acute angle between the two reflected lines with a protractor. The expected angle is about $\mathbf{25}^\circ$.

3(d)(iii)

  • The results suggest $\alpha = \theta_2 - \theta_1$.
  • For example, $40^\circ - 15^\circ = 25^\circ$, which agrees with an angle $\alpha$ of about $25^\circ$.

3(e)

  • Use a sharp pencil to draw thin lines, so their positions can be marked more precisely.

3(f)

  • Different students may align the pins slightly differently because the pins have a finite thickness.
Original question

Log in or create account

IGCSE, A-Level & AP