Skip to content

IGCSE Physics · June 2022 · Paper 52 · Difficulty 3 · Standard

Question 2

2

In this experiment, you will investigate the resistances of combinations of resistors.

Carry out the following instructions, referring to Fig. 2.1. The circuit has been set up for you.

(a)

Close the switch.

(i)

Measure the current $I_1$ in the circuit.

$I_1$ = A[1]

(ii)

Measure the potential difference (p.d.) $V_1$ across resistors $R_A$ and $R_B$ in series.

$V_1$ = V[1]

(iii)

Open the switch.

Calculate the resistance $R_1$ of the combination of resistors in series. Use the equation

$R_1 = \frac{V_1}{I_1}$

Include the unit.

$R_1$ = [1]

(b)

Disconnect the voltmeter. Connect resistor $R_C$ in parallel with resistors $R_A$ and $R_B$.

Do not change the series combination of resistors $R_A$ and $R_B$.

Connect the voltmeter across the combination of all three resistors.

(i)

Draw a circuit diagram showing the circuit described in (b).[2]

(ii)

Close the switch.

Measure the current $I_2$ in the circuit.

$I_2$ = A

Measure the potential difference $V_2$ across the combination of the three resistors.

$V_2$ = V

Open the switch.

Calculate the resistance $R_2$ of the combination of resistors. Use the equation

$R_2 = \frac{V_2}{I_2}$

Include the unit.

$R_2$ = [2]

(c)

Disconnect the voltmeter. Rearrange the resistors to set up the circuit shown in Fig. 2.2.

Close the switch.

Measure the current $I_3$ in the circuit.

$I_3$ = A

Measure the potential difference $V_3$ across the combination of the three resistors.

$V_3$ = V

Open the switch.

Calculate the resistance $R_3$ of the combination of resistors. Use the equation

$R_3 = \frac{V_3}{I_3}$

Include the unit. Give your answer to a suitable number of significant figures for this experiment.

$R_3$ = [2]

(d)

A student thinks the three resistors $R_A$, $R_B$ and $R_C$ have the same resistance within the limits of experimental accuracy.

Suggest how the student could use the apparatus provided to test his idea.

[2]

[Total: 11]

Show the mark scheme

These are the official mark-scheme rows. Each point that matches your answer earns a mark.

Tap the mark scheme to open it full size.

Show a worked answer

How to reach each mark, step by step. Try the question yourself first.

2(a)(i)

  • Close the switch and read the ammeter. Record your measured $I_1$ in amperes to at least two decimal places; it should be below $1\,\mathrm{A}$.

2(a)(ii)

  • Read the voltmeter across both resistors. Record your measured $V_1$ in volts to at least one decimal place; it should be below $3\,\mathrm{V}$.

2(a)(iii)

  • Use $R_1 = V_1 / I_1$. Divide your measured voltage in volts by your current in amperes to find $R_1$ in ohms.
  • $R_1 = \mathbf{V_1 / I_1}$. Give the result in ohms.

2(b)(i)

  • Draw $R_A$ and $R_B$ in series in one branch, with $R_C$ in a parallel branch.
  • Connect the voltmeter across the whole resistor combination. Put the ammeter, switch and supply in series with the combination.

2(b)(ii)

  • Read $I_2$ and $V_2$ with the switch closed. $I_2$ should be greater than $I_1$, while $V_2$ should be within $0.5\,\mathrm{V}$ of $V_1$.
  • Open the switch. Use $R_2 = V_2 / I_2$; divide your voltage in volts by your current in amperes.
  • $R_2 = \mathbf{V_2 / I_2}$. Give the result in ohms.

2(c)

  • With the switch closed, read $I_3$ and $V_3$, then open the switch. The values depend on your apparatus.
  • Use $R_3 = V_3 / I_3$. Divide the measured voltage in volts by the current in amperes and round to two or three significant figures.
  • $R_3 = \mathbf{V_3 / I_3}$. Give the result in ohms.

2(d)

  • Measure the potential difference $V$ and current $I$ for each resistor, then use $R = V/I$ to find each resistance.
  • Compare the three values. They support the idea if they are close within experimental uncertainty, such as within $10\%$.
Original question

Log in or create account

IGCSE, A-Level & AP