Skip to content

IGCSE Physics · June 2021 · Paper 53 · Difficulty 4 · Challenging

Question 2

2

In this experiment, you will determine the electromotive force (e.m.f.) and resistance of a cell by using a resistance wire.

The circuit has been set up for you.

Carry out the following instructions, referring to Fig. 2.1.

Fig. 2.1
(a)

Close the switch.

Attach the crocodile clip to the resistance wire. Adjust its position until the value $V$ of the potential difference (p.d.) across the cell and the resistor is 5.0 V.

Measure, and record in Table 2.1, the value of the current $I$ for the cell and resistor in series.

Repeat this procedure for values of $V = 4.5\text{ V}$, 4.0 V, 3.5 V and 3.0 V. Detach the crocodile clip from the resistance wire.

Open the switch.

Table 2.1

$V / \text{V}$$I / \text{A}$
5.0
4.5
4.0
3.5
3.0

[2]

(b)

Plot a graph of $I /\text{A}$ ($y$-axis) against $V/\text{V}$ ($x$-axis). Start both axes at the origin (0, 0).

[4]

(c)

The e.m.f. $E$ of the cell is equal to the value of $V$ when $I = 0.0\text{ A}$.

Determine the value of $E$ from the graph.

$E =$ [1]

(d)
(i)

Determine the gradient $G$ of the graph. Show clearly on the graph how you obtained the necessary information.

$G =$ [1]

(ii)

The value of $\frac{1}{G}$ is numerically equal to the resistance $(r + R)$ where $r$ is the resistance of the cell and $R = 5.0\,\Omega$.

Calculate the resistance $r$ of the cell.

$r =$ $\Omega$[1]

(e)

Suggest how the experiment and graph could be improved to obtain a more accurate value for e.m.f. $E$.

[2]

[Total: 11]

Show the mark scheme

These are the official mark-scheme rows. Each point that matches your answer earns a mark.

Tap the mark scheme to open it full size.

Show a worked answer

How to reach each mark, step by step. Try the question yourself first.

2(a)

  • Record the ammeter reading in $\mathrm{A}$ for each of the five voltages. The readings depend on your circuit.
  • Check that all five currents are below $1.00\,\mathrm{A}$ and decrease as the listed voltage decreases.

2(b)

  • Label the horizontal axis $V/\mathrm{V}$ and the vertical axis $I/\mathrm{A}$. Start both at zero.
  • Choose even scales so the points fill at least half the grid. Plot each measured pair to within half a small square.
  • Draw a thin, well judged line of best fit through the trend of the points.

2(c)

  • Extend the best-fit line to $I = 0\,\mathrm{A}$ and read its intercept on the voltage axis. This is $E$; expect $\mathbf{1.0}$ to $\mathbf{2.0}\,\mathrm{V}$.

2(d)(i)

  • Draw a large triangle on the best-fit line. Read the changes in current and voltage from its corners.
  • Use $G = \mathbf{\Delta I/\Delta V}$. Divide the current change in $\mathrm{A}$ by the voltage change in $\mathrm{V}$. Record the gradient in $\mathrm{A/V}$.

2(d)(ii)

  • Use $1/G = r+R$, so $r = \mathbf{1/G-R}$.
  • Substitute your measured gradient, including its $\mathrm{A/V}$ unit, and $R = 5.0\,\mathrm{\Omega}$. The reciprocal $1/G$ is in $\mathrm{\Omega}$; subtract $5.0\,\mathrm{\Omega}$ to find $r$.

2(e)

  • Take more readings at other potential differences, so that the line of best fit is better supported by the data.
  • Start the potential difference axis at $1.0\,\mathrm{V}$ and use a larger scale, so that the intercept can be read more precisely.
Original question

Log in or create account

IGCSE, A-Level & AP