Skip to content

IGCSE Physics · June 2021 · Paper 53 · Difficulty 3 · Standard

Question 1

1

In this experiment, you will investigate the behaviour of a spring and use it to determine the density of modelling clay.

A stand and spring have been set up for you.

Carry out the following instructions, referring to Fig. 1.1 and Fig. 1.2.

(a)

Measure the length $l_0$ of the spring without any load.

$l_0 =$ $cm$[1]

(b)

Suspend a load of weight $W = 2.0\text{N}$ from the spring, as shown in Fig. 1.2.

(i)

Measure the stretched length $l$ of the spring.

$l =$ $cm$[1]

(ii)

Calculate the extension $e$ of the spring for a load of weight $W = 2.0\text{N}$. Use your values from (a) and (b)(i) and the equation $e = (l - l_0)$.

$e =$ $cm$[1]

(c)

Remove the load from the spring.

Suspend the load U, which is made of modelling clay, from the spring.

Measure the stretched length $l_U$ of the spring.

$l_U =$ $cm$

Calculate the extension $e_U$ of the spring with load U.

$e_U =$ $cm$

The extension of a spring is directly proportional to the weight of the load.

Use your values of $W$ and $e$ from (b)(ii) and your value of $e_U$ to determine the weight $W_U$ of load U.

Show your working.

$W_U =$ [2]

(d)

Fully immerse load U in the beaker of water, as shown in Fig. 1.3. The load U must not touch either the sides or the bottom of the beaker.

Measure the stretched length $l_W$ of the spring.

$l_W =$ $cm$

Calculate the extension $e_W$ of the spring with load U in the water.

$e_W =$ $cm$

Calculate the density $\rho$ of the modelling clay.

Use your value of $e_U$ from (c), your value of $e_W$ and the equation $\rho = \frac{e_U}{(e_U - e_W)} \times k$, where $k = 1.0\text{g/cm}^3$.

$\rho =$ $\text{g/cm}^3$[2]

(e)

Suggest a possible source of inaccuracy in the determination of $\rho$ in this experiment.[1]

(f)

Describe one precaution that you took when measuring the length of the spring, to ensure an accurate reading. You may draw a diagram.[1]

(g)

A student plots a graph of load against extension for the spring, to show that the two quantities are directly proportional.[2]

State how his graph line shows that load and extension are directly proportional.

[Total: 11]

Show the mark scheme

These are the official mark-scheme rows. Each point that matches your answer earns a mark.

Tap the mark scheme to open it full size.

Show a worked answer

How to reach each mark, step by step. Try the question yourself first.

1(a)

  • Measure the unloaded spring from one end of its coils to the other. Record $l_0$ in $\mathrm{cm}$ to the nearest $0.1\,\mathrm{cm}$. The result depends on your spring.

1(b)(i)

  • With the $2.0\,\mathrm{N}$ load attached, measure the same part of the spring. Record $l$ in $\mathrm{cm}$; it should be greater than $l_0$.

1(b)(ii)

  • Use $e = \mathbf{l-l_0}$ to find the increase in length. Subtract your unloaded length from your stretched length, both in $\mathrm{cm}$; the extension is also in $\mathrm{cm}$.

1(c)

  • Measure $l_U$ in $\mathrm{cm}$, then use $e_U = l_U-l_0$ to find its extension in $\mathrm{cm}$.
  • Extension is proportional to load, so $W_U/W = e_U/e$.
  • Using your extensions in $\mathrm{cm}$, $W_U = (2.0\,\mathrm{N})(e_U/e)$. Your result is $W_U = \mathbf{2.0e_U/e}\,\mathrm{N}$; expect about $1.0$ to $1.4\,\mathrm{N}$.

1(d)

  • Measure $l_W$ with the clay fully under water, then use $e_W = l_W-l_0$. Both lengths are in $\mathrm{cm}$; $l_W$ should be less than $l_U$.
  • Use $\rho = \frac{e_U}{e_U-e_W}k$. The difference in extensions is due to the upthrust of the water.
  • With both extensions in $\mathrm{cm}$, $\rho = \frac{e_U}{e_U-e_W}(1.0\,\mathrm{g/cm^3}) = \mathbf{\frac{1.0e_U}{e_U-e_W}}\,\mathrm{g/cm^3}$. Expect $1.0$ to $2.0\,\mathrm{g/cm^3}$.

1(e)

  • Air bubbles may stick to the immersed clay. These increase the upthrust and affect the calculated density.

1(f)

  • Place the rule close to and parallel to the spring, so that the length can be read accurately.

1(g)

  • The graph is a straight line and passes through the origin. This shows that the ratio of load to extension is constant.
Original question

Log in or create account

IGCSE, A-Level & AP