Skip to content

IGCSE Physics · June 2021 · Paper 51 · Difficulty 3 · Standard

Question 2

2

In this experiment, you will investigate resistance.

Carry out the following instructions, referring to Fig. 2.1. The circuit has been set up for you.

Fig. 2.1
(a)

Close the switch.

(i)

Record the current $I_1$ in the circuit.

$I_1$ = [1]

(ii)

Record the potential difference (p.d.) $V_1$ across the resistor.

$V_1$ = [1]

Open the switch.

(iii)

Calculate the resistance $R_1$ of the resistor using the equation $R_1 = \frac{V_1}{I_1}$.

$R_1$ = [1]

(b)

Disconnect the voltmeter.

Connect the second resistor provided in series with the first resistor.

Connect the voltmeter across both resistors.

Close the switch.

  • Record the current $I_2$ in the circuit.

$I_2$ =

  • Record the potential difference (p.d.) $V_2$ across the resistors.

$V_2$ =

Open the switch.

  • Calculate the resistance $R_S$ of the resistors in series using the equation $R_S = \frac{V_2}{I_2}$.

$R_S$ = [2]

(c)

Disconnect the voltmeter. Connect the second resistor in parallel with the first resistor.

Connect the voltmeter across both resistors.

Close the switch.

  • Record the current $I_3$ in the circuit.

$I_3$ =

  • Record the potential difference (p.d.) $V_3$ across the resistors.

$V_3$ =

Open the switch.

  • Calculate the resistance $R_P$ of the resistors in parallel using the equation $R_P = \frac{V_3}{I_3}$.

$R_P$ = [2]

(d)

Complete the circuit diagram to show the circuit you used in part (c).

[2]

(e)

Describe how you would extend part (c) of this experiment to investigate the relationship between the combined resistance of identical resistors connected in parallel and the number of resistors. You are not required to do this investigation.[2]

[Total: 11]

Show the mark scheme

These are the official mark-scheme rows. Each point that matches your answer earns a mark.

Tap the mark scheme to open it full size.

Show a worked answer

How to reach each mark, step by step. Try the question yourself first.

2(a)(iii)

  • Use $R_1 = V_1/I_1$. Substitute your measured $V_1$ in $\mathrm{V}$ and $I_1$ in $\mathrm{A}$; the resistance is in $\mathrm{\Omega}$.

2(b)

  • Record $I_2$ in $\mathrm{A}$ and $V_2$ in $\mathrm{V}$. $I_2 < I_1$ because adding a resistor in series increases the total resistance.
  • Use $R_S = V_2/I_2$. Substitute your measured voltage and current, with their units, to obtain $R_S$ in $\mathrm{\Omega}$.

2(c)

  • Record $I_3$ in $\mathrm{A}$ and $V_3$ in $\mathrm{V}$. $I_3 > I_1$ because adding a parallel branch reduces the total resistance.
  • Use $R_P = V_3/I_3$. Substitute your measured voltage and current, with their units, to obtain $R_P$ in $\mathrm{\Omega}$. It should be less than $R_1$.

2(d)

  • Draw the two resistors in parallel, with the ammeter in series with the supply and the parallel pair.
  • Connect the voltmeter across the parallel pair and include the switch in series.

2(e)

  • Add at least three more identical resistors in parallel, one at a time.
  • After each addition measure the total current and p.d., and use $R=V/I$ to find the combined resistance.
Original question

Log in or create account

IGCSE, A-Level & AP