Skip to content

IGCSE Physics · June 2020 · Paper 51 · Difficulty 3 · Standard

Question 2

2

In this experiment, you will determine the resistances of filament lamps.

Carry out the following instructions, referring to Fig. 2.1.

Fig. 2.1
(a)

Switch on.

(i)

Measure the current $I_1$ in the circuit.

$I_1$ = A[1]

(ii)

Measure the potential difference $V_1$ across lamp $L_1$.

$V_1$ = V[1]

Switch off.

(iii)

Calculate the resistance $R_1$ of the filament of lamp $L_1$. Use the equation $R_1 = \frac{V_1}{I_1}$. Include the unit.

$R_1$ = [2]

(b)

Disconnect the voltmeter. Connect lamp $L_2$ in series with lamp $L_1$. Connect the voltmeter across lamp $L_2$. Switch on.

Measure the current $I_2$ in the circuit.

$I_2$ = A

Measure the potential difference $V_2$ across lamp $L_2$.

$V_2$ = V

Switch off.

Calculate the resistance $R_2$ of the filament of lamp $L_2$. Use the equation $R_2 = \frac{V_2}{I_2}$.

$R_2$ = [1]

(c)

Disconnect the voltmeter. Connect lamp $L_3$ in series with lamps $L_1$ and $L_2$. Connect the voltmeter across lamp $L_3$. Switch on.

Measure the current $I_3$ in the circuit.

$I_3$ = A

Measure the potential difference $V_3$ across lamp $L_3$.

$V_3$ = V

Switch off.

Calculate the resistance $R_3$ of the filament of lamp $L_3$. Use the equation $R_3 = \frac{V_3}{I_3}$.

$R_3$ = [1]

(d)

Calculate $R_1 + R_2 + R_3$. Give your answer to a suitable number of significant figures for this experiment.

$R_1 + R_2 + R_3$ = [1]

(e)

Some students make suggestions about the results of the experiment.

Suggestion A: $R_1 + R_2 + R_3$ should be equal to $3 \times R_1$.

Suggestion B: $R_1 + R_2 + R_3$ should be less than $3 \times R_1$.

Suggestion C: $R_1 + R_2 + R_3$ should be greater than $3 \times R_1$.

State which suggestion, A, B or C, agrees with your results. Justify your answer by reference to your results.

statement

justification

[2]

(f)

A student investigates whether the statement in (e) is always true for the same three lamps connected in series.

State a variable that he changes and how he changes the variable. You are not required to do this extra experiment.

variable to change

method of changing the variable

[2]

[Total: 11]

Show the mark scheme

These are the official mark-scheme rows. Each point that matches your answer earns a mark.

Tap the mark scheme to open it full size.

Show a worked answer

How to reach each mark, step by step. Try the question yourself first.

2(a)(i)

  • Read the ammeter with the circuit switched on. Record your measured $I_1$ in amperes to at least two decimal places; it should be less than $1\,\mathrm{A}$.

2(a)(ii)

  • Read the voltmeter across lamp $L_1$. Record your measured $V_1$ in volts to at least one decimal place; it should be less than $3\,\mathrm{V}$.

2(a)(iii)

  • Use $R_1 = V_1/I_1$. For example, if $V_1 = 2.0\,\mathrm{V}$ and $I_1 = 0.20\,\mathrm{A}$, then $R_1 = (2.0\,\mathrm{V})/(0.20\,\mathrm{A}) = \mathbf{10}\,\Omega$. Use your readings.

2(b)

  • Measure $I_2$ in series and $V_2$ across $L_2$. Use $R_2 = V_2/I_2$.
  • For example, $(0.80\,\mathrm{V})/(0.10\,\mathrm{A}) = \mathbf{8.0}\,\Omega$. Use your own readings; $R_2$ should be less than $R_1$.

2(c)

  • Measure $I_3$ in series and $V_3$ across $L_3$. Use $R_3 = V_3/I_3$.
  • For example, $(0.42\,\mathrm{V})/(0.07\,\mathrm{A}) = \mathbf{6.0}\,\Omega$. Use your own readings; $R_3$ should be less than $R_1$ or $R_2$.

2(d)

  • Add the three measured resistances: $R_{\mathrm{total}} = R_1 + R_2 + R_3$. For example, $R_{\mathrm{total}} = 10\,\Omega + 8.0\,\Omega + 6.0\,\Omega = \mathbf{24}\,\Omega$. Use your results and give 2 or 3 significant figures.

2(e)

  • Compare your sum $R_1 + R_2 + R_3$ with $3R_1$ and choose the matching statement. Quote both values as evidence.
  • For example, if $R_1 = 10\,\Omega$, $R_2 = 8.0\,\Omega$ and $R_3 = 6.0\,\Omega$, the sum is $24\,\Omega$ and $3R_1 = 30\,\Omega$. The sum is less, so choose B.

2(f)

  • Change the potential difference across the lamps to test another setting.
  • Adjust the power supply, or add a variable resistor and adjust it.
Original question

Log in or create account

IGCSE, A-Level & AP