Skip to content

IGCSE Physics · June 2020 · Paper 51 · Difficulty 3 · Standard

Question 3

3

In this experiment you will investigate the position of the image in a plane mirror.

Carry out the following instructions, using the separate ray-trace sheet provided. You may refer to Fig. 3.1 for guidance.

(a)
(i)

Draw a line 10cm long near the middle of the ray-trace sheet. Label the line MR. Draw a normal to this line that passes through the centre of MR. Label the normal NL. Label the point at which NL crosses MR with the letter B.[1]

(ii)

Draw a line 7.0cm long from B at an angle of incidence $i = 30^{\circ}$ to the normal below MR and to the left of the normal. Label the end of this line A.[1]

(iii)

Place a pin $P_1$ on line AB at a distance 6.0cm from B.

Place a pin $P_2$ on line AB close to MR.[1]

(b)
(i)

Place the reflecting face of the mirror vertically on the line MR.

View the images of pins $P_1$ and $P_2$ from the direction indicated by the eye in Fig. 3.1.

Place two pins $P_3$ and $P_4$ some distance apart so that pin $P_3$ and the images of $P_2$ and $P_1$ all appear exactly behind pin $P_4$. Label the positions of $P_3$ and $P_4$.

Remove the pins and the mirror and draw the line joining the positions of $P_3$ and $P_4$.[1]

(ii)

Continue the line until it extends at least 7.0cm beyond MR.[1]

(c)

Replace pin $P_1$ on line AB at a distance 6.0cm from B.

Place pin $P_2$ 1.0cm to the right of its position in part (a).

Repeat the steps in part (b).

Label with the letter Y the point where the two lines cross beyond MR.

(i)

Draw a line from $P_1$ to MR that meets MR at a right angle. Measure and record the length $a$ of this line.

$a = .....................................................$[1]

(ii)

Draw a line from the point labelled Y to MR that meets MR at a right angle. Measure and record the length $b$ of this line.

$b = .....................................................$[1]

(d)
(i)

Replace the mirror on MR. Place pin $P_1$ on the normal at a distance 6.0cm from the front of the mirror.

View the image of $P_1$ in the mirror.

Place pin $P_2$ on the normal behind the mirror.

Adjust the position of $P_2$ along the normal so that the image of the bottom of the pin $P_1$ seen in the mirror and the top of pin $P_2$ seen over the mirror appear as one pin when viewed from all angles in front of the mirror.

Label the position of $P_2$.[1]

(ii)

Remove the pins and the mirror.

Measure the distance $x$ along the normal between $P_2$ and the mirror.

$x = .....................................................$[2]

(e)

A student carries out this experiment with care.

Suggest a practical reason why the results may not be accurate.

[1]

Tie your ray-trace sheet into this booklet between pages 8 and 9.

[Total: 11]

Show the mark scheme

These are the official mark-scheme rows. Each point that matches your answer earns a mark.

Tap the mark scheme to open it full size.

Show a worked answer

How to reach each mark, step by step. Try the question yourself first.

3(a)(i)

  • Draw MR 10 cm long. Draw NL through its centre at $90^\circ$ to MR, and label the crossing B.

3(a)(ii)

  • Draw AB 7.0 cm long below MR and to the left of the normal, at $30^\circ$ to the normal.

3(a)(iii)

  • Put P1 6.0 cm from B on AB. Put P2 close to MR, at least 5.0 cm from P1.

3(b)(i)

  • Line up P3 and P4 with the images of P1 and P2. Remove the pins and mirror, then draw a neat line through P3 and P4.

3(b)(ii)

  • Extend the line through P3 and P4 at least 7.0 cm beyond MR.

3(c)(i)

  • Draw a perpendicular from $P_1$ to $MR$ and measure it. The expected distance is $a=d\cos i$.
  • $a=(6.0\,\mathrm{cm})\cos 30^\circ\approx\mathbf{5.2}\,\mathrm{cm}$. Record your own measured value.

3(c)(ii)

  • Draw a perpendicular from $Y$ to $MR$ and measure its length $b$. The image is as far behind a plane mirror as the object is in front, so $b$ should be close to $a$, about $\mathbf{5.2}\,\mathrm{cm}$.

3(d)(i)

  • Put P1 on the normal 6.0 cm in front of the mirror. Move P2 along the normal behind it until P2 and the image of P1 appear as one pin from all viewing angles.

3(d)(ii)

  • Measure along the normal from $P_2$ to the reflecting face of the mirror. Record your measured $x$ in cm; it should be about $\mathbf{6.0}\,\mathrm{cm}$.

3(e)

  • The pins have thickness, so it is hard to judge exactly when they line up with the images.
Original question

Log in or create account

IGCSE, A-Level & AP