Skip to content

IGCSE Physics · March 2025 · Paper 52 · Difficulty 3 · Standard

Question 2

2

In this experiment, you will investigate the effect of insulation on the cooling of water.

Refer to Fig. 2.1.

Beaker A is covered with material that is a thermal insulator.

Beaker B is identical to beaker A but has no insulation.

(a)

• Pour $200\text{ cm}^3$ of hot water into beaker A.

  • Place the thermometer in the water.
  • In the first row of Table 2.1, record the temperature $\theta$ of the water at time $t = 0$ and immediately start the stop-watch.
  • Record, in Table 2.1, the temperature $\theta$ of the water at times $t = 30\text{ s}$, $t = 60\text{ s}$, $t = 90\text{ s}$, $t = 120\text{ s}$, $t = 150\text{ s}$ and $t = 180\text{ s}$.

[1]

Remove the thermometer from the beaker.

(b)

Repeat the procedure in (a) for beaker B.[2]

Table 2.1

beaker A with insulationbeaker B without insulation
$t\text{ /s}$$\theta\text{ / }^\circ\text{C}$$\theta\text{ / }^\circ\text{C}$
0
30
60
90
120
150
180
(c)

Write a conclusion stating whether the insulation affects the rate of cooling of the water. Justify your answer by referring to values from your results.[2]

(d)
(i)

Calculate the average cooling rate $x_1$ during the first half of the experiment for the water in beaker B. Use your readings for beaker B from Table 2.1 and the equation:

$$x_1 = \frac{\theta_0 - \theta_{90}}{T},$$

where $T = 90\text{ s}$ and $\theta_0$ and $\theta_{90}$ are the temperatures of the water in beaker B at times $t = 0$ and $t = 90\text{ s}$.

Include the unit.

$x_1 =$ [1]

(ii)

Calculate the average cooling rate $x_2$ during the second half of the experiment for the water in beaker B. Use your readings for beaker B from Table 2.1 and the equation:

$$x_2 = \frac{\theta_{90} - \theta_{180}}{T}$$

where $T = 90\text{ s}$ and $\theta_{90}$ and $\theta_{180}$ are the temperatures of the water in beaker B at times $t = 90\text{ s}$ and $t = 180\text{ s}$.

Include the unit.

$x_2 =$ [1]

(e)

A student suggests that, for this type of experiment, the temperature of the water in each beaker at time $t = 0$ must be the same for the comparison to be fair.

Use your answers from (d)(i) and (d)(ii) to explain whether this is necessary.[2]

(f)
(i)

A student wants to eliminate, from the comparison, any thermal energy lost from the surface of the water.

Suggest a change to the equipment which will do that.

You are not required to carry out this additional experiment.[1]

(ii)

Suggest what effect this change will have on the cooling rates of the water in beaker A and beaker B.[1]

[Total: 11]

Show the mark scheme

These are the official mark-scheme rows. Each point that matches your answer earns a mark.

Tap the mark scheme to open it full size.

Show a worked answer

How to reach each mark, step by step. Try the question yourself first.

2(a)

  • Record the measured temperature at each of the seven times. The readings should decrease as the water cools.

2(b)

  • Record the measured temperature of beaker B at each time. Its readings should decrease as the water cools.
  • Beaker B should cool faster than beaker A because it has no insulation.

2(c)

  • The insulation makes the water cool more slowly: the temperature drop in beaker A is smaller than the drop in beaker B over $180\,\mathrm{s}$.
  • For each beaker, subtract its temperature at $180\,\mathrm{s}$ from its temperature at $0\,\mathrm{s}$. Quote both drops from your readings to support the conclusion.

2(d)(i)

  • Use $x_1 = (\theta_0 - \theta_{90})/T$: temperature fall divided by time taken.
  • With your temperatures in $\mathrm{^{\circ}C}$ and $T = 90\,\mathrm{s}$, $x_1 = \mathbf{\frac{\theta_0 - \theta_{90}}{90}}\,\mathrm{^{\circ}C/s}$.
  • Use your beaker B readings at $0\,\mathrm{s}$ and $90\,\mathrm{s}$. The printed table is blank, so there is no fixed numerical answer.

2(d)(ii)

  • Use $x_2 = (\theta_{90} - \theta_{180})/T$: temperature fall divided by time taken.
  • With your temperatures in $\mathrm{^{\circ}C}$ and $T = 90\,\mathrm{s}$, $x_2 = \mathbf{\frac{\theta_{90} - \theta_{180}}{90}}\,\mathrm{^{\circ}C/s}$.
  • Use your beaker B readings at $90\,\mathrm{s}$ and $180\,\mathrm{s}$. Normally $x_2 < x_1$: cooler water loses heat more slowly because its temperature is closer to room temperature.

2(e)

  • Compare $x_1$ and $x_2$: the water generally cools faster when it is hotter, so $x_1 > x_2$.
  • Yes, the beakers should start at the same temperature, so the comparison depends on insulation rather than starting temperature.

2(f)(i)

  • Put a lid on each beaker to reduce energy loss from the water surface.

2(f)(ii)

  • Both cooling rates decrease because less energy leaves from the water surfaces.
Original question

Log in or create account

IGCSE, A-Level & AP