Skip to content

IGCSE Physics · November 2025 · Paper 63 · Difficulty 4 · Challenging

Question 2

2

A student investigates the resistances of identical wires connected in parallel.

She uses the circuit shown in Fig. 2.1.

Fig. 2.1
(a)

On Fig. 2.1, draw a voltmeter connected so that it will measure the potential difference (p.d.) across terminals X and Y.[1]

Circuit A

(b)

The student connects crocodile clip A to a length $l = 80.0\text{ cm}$ of resistance wire A.

(i)

On Fig. 2.2, draw an arrow ($\longleftrightarrow$) to indicate precisely between which two points she should measure $l = 80.0\text{ cm}$ for wire A.

Fig. 2.2

[1]

(ii)

The student measures the potential difference $V$ across terminals X and Y and measures the current $I$ in the circuit.

The readings on the meters are shown in Fig. 2.3 and Fig. 2.4.

Fig. 2.3 Fig. 2.4

Read, and record in the first line of Table 2.1, the values of $V$ and $I$ shown on the meters in Fig. 2.3 and Fig. 2.4.

Table 2.1

circuit$V / \text{V}$$I / \text{A}$$R / \Omega$
A
B2.20.59
C1.80.72

[2]

(c)

Circuit B The student connects crocodile clip B to a length $l = 80.0\text{ cm}$ of resistance wire B so that wires A and B are connected in parallel.

Circuit C The student connects crocodile clip C to a length $l = 80.0\text{ cm}$ of resistance wire C so that wires A, B and C are connected in parallel.

In each circuit, she measures the potential difference $V$ across terminals X and Y and measures the current $I$ in the circuit.

Her readings are shown in Table 2.1.

Calculate, and record in Table 2.1, the resistance $R$ of each wire combination. Use the equation:

$$R = \frac{V}{I}.$$

[2]

(d)
(i)

Record a resistance $R_{\text{A}}$. $R_{\text{A}}$ is the value of $R$ from Circuit A.

$R_{\text{A}} =$ $\Omega$

Calculate a resistance $R_{\text{B}}$. Use the value of $R$ from Circuit B and the equation:

$$R_{\text{B}} = R \times 2$$

$R_{\text{B}} =$ $\Omega$

Calculate a resistance $R_{\text{C}}$. Use the value of $R$ from Circuit C and the equation:

$$R_{\text{C}} = R \times 3$$

$R_{\text{C}} =$ $\Omega$[1]

(ii)

A student suggests that the values of $R_{\text{A}}$, $R_{\text{B}}$ and $R_{\text{C}}$ should be equal.

State whether your results support this suggestion. Use values from your results to justify your answer.

statement

justification [2]

(e)

Briefly explain why resistor $\text{R}_{\text{P}}$, shown in Fig. 2.1, must remain in place throughout the experiment.[1]

(f)

One possible problem with this type of experiment is heating of the resistance wires. Suggest what to do to reduce this.[1]

[Total: 11]

Show the mark scheme

These are the official mark-scheme rows. Each point that matches your answer earns a mark.

Tap the mark scheme to open it full size.

Show a worked answer

How to reach each mark, step by step. Try the question yourself first.

2(a)

  • Draw a voltmeter symbol connected in parallel between X and Y.

2(b)(i)

  • Draw the arrow from the left-hand end of the wire to the left-hand side of clip A.

2(b)(ii)

  • Read the two meter scales: $V = \mathbf{2.9}\,\mathrm{V}$ and $I = \mathbf{0.36}\,\mathrm{A}$.

2(c)

  • Use $R = V/I$ for each circuit.
  • A: $R = (2.9\,\mathrm{V})/(0.36\,\mathrm{A}) = \mathbf{8.1}\,\Omega$. B: $R = (2.2\,\mathrm{V})/(0.59\,\mathrm{A}) = \mathbf{3.7}\,\Omega$.
  • C: $R = (1.8\,\mathrm{V})/(0.72\,\mathrm{A}) = \mathbf{2.5}\,\Omega$. All three results are to two significant figures.

2(d)(i)

  • Use $R_A = R$ for A, $R_B = 2R$ for B and $R_C = 3R$ for C.
  • $R_A = \mathbf{8.1}\,\Omega$; $R_B = 2(3.7\,\Omega) = \mathbf{7.4}\,\Omega$; $R_C = 3(2.5\,\Omega) = \mathbf{7.5}\,\Omega$.

2(d)(ii)

  • Yes, the results support the suggestion within experimental uncertainty.
  • The values $8.1\,\Omega$, $7.4\,\Omega$ and $7.5\,\Omega$ differ by less than about $10\%$.

2(e)

  • $R_P$ limits the current, preventing it from exceeding the ammeter range.

2(f)

  • Switch off between readings so current flows for less time and the wires heat up less.
Original question

Log in or create account

IGCSE, A-Level & AP