Skip to content

IGCSE Physics · November 2025 · Paper 63 · Difficulty 3 · Standard

Question 1

1

A student determines the volume of a block of modelling clay by two methods.

Method 1

He measures the block of modelling clay shown full size in Fig. 1.1.

(a)
(i)

Measure the length $l$, width $w$ and height $h$ of the block of modelling clay on Fig. 1.1. Record your values in centimetres to the nearest millimetre.

length $l$ = cm

width $w$ = cm

height $h$ = cm[2]

(ii)

Calculate a value $V_A$ for the volume of the block. Use your measurements from (a)(i) and the equation:

$V_A = l \times w \times h$.

$V_A$ = cm$^{3}$[1]

(b)

Suggest why $V_A$ is only an approximate value for the volume of the block.

Describe how the accuracy of $V_A$ can be improved.

suggestion

improvement

[2]

(c)

Another student measures the dimensions of a block of clay which is much smaller than the block in (a). Suggest why these measurements may not be as accurate as yours, even if they are done carefully.

[1]

Method 2

(d)
(i)

The student pours water into a measuring cylinder.

Record the volume $V_1$ of the water in the measuring cylinder shown in Fig. 1.2.

$V_1$ = cm$^{3}$[1]

(ii)

Describe briefly how a measuring cylinder is read to obtain an accurate value for the volume of water.

[1]

(e)

The student lowers the modelling clay into the water using a loop of thread, as shown in Fig. 1.3.

Record the new reading $V_2$ shown on the measuring cylinder scale in Fig. 1.3.

$V_2$ = cm$^{3}$

Calculate another value $V_B$ for the volume of the block.

Use your measurements from (d)(i) and (e) and the equation: $V_B = (V_2 - V_1)$.

$V_B$ = cm$^{3}$[1]

(f)

Suggest one possible source of inaccuracy in Method 2 and suggest one improvement to reduce its effect.

source of inaccuracy

improvement

[2]

[Total: 11]

Show the mark scheme

These are the official mark-scheme rows. Each point that matches your answer earns a mark.

Tap the mark scheme to open it full size.

Show a worked answer

How to reach each mark, step by step. Try the question yourself first.

1(a)(i)

  • Measure each dimension on the full-size figure: $l = \mathbf{6.9}\,\mathrm{cm}$, $w = \mathbf{2.5}\,\mathrm{cm}$ and $h = \mathbf{3.0}\,\mathrm{cm}$.

1(a)(ii)

  • Use $V_A = lwh$.
  • $V_A = (6.9\,\mathrm{cm})(2.5\,\mathrm{cm})(3.0\,\mathrm{cm}) = \mathbf{52}\,\mathrm{cm^3}$.

1(b)

  • The block is not perfectly regular, so its dimensions vary from place to place.
  • Measure each dimension at several places and take the average for each one.

1(c)

  • The same ruler uncertainty is a larger percentage of a smaller dimension.

1(d)(i)

  • Read the water level on the scale: $V_1 = \mathbf{152}\,\mathrm{cm^3}$.

1(d)(ii)

  • Read the bottom of the meniscus at eye level, with the line of sight perpendicular to the scale, to avoid parallax.

1(e)

  • Read the bottom of the meniscus: $V_2 = \mathbf{206}\,\mathrm{cm^3}$. The first reading is $V_1 = 152\,\mathrm{cm^3}$.
  • Use $V_B = V_2 - V_1$.
  • $V_B = 206\,\mathrm{cm^3} - 152\,\mathrm{cm^3} = \mathbf{54}\,\mathrm{cm^3}$.

1(f)

  • The thread displaces water, increasing the measured volume.
  • Use a thinner thread to reduce the extra displaced volume.
Original question

Log in or create account

IGCSE, A-Level & AP