Skip to content

IGCSE Physics · November 2025 · Paper 53 · Difficulty 3 · Standard

Question 2

2

In this experiment, you will investigate the resistances of identical wires connected in parallel.

A circuit has been set up for you. Resistor $R_P$ must remain in place throughout the experiment.

Refer to Fig. 2.1.

Circuit A

Move crocodile clip A to a length $l = 95.0\text{ cm}$ of resistance wire A.

(a)

Close the switch.

Measure, and record in Table 2.1, the values of potential difference (p.d.) $V$ across the resistance wire and current $I$ in the circuit.

Open the switch.

Table 2.1

circuitV/VI /AR/$\Omega$
A
B
C

[2]

Circuit B

Do not disconnect crocodile clip A.

Connect crocodile clip B to a length $l = 95.0\text{ cm}$ of resistance wire B.

It does not matter if crocodile clip A and crocodile clip B touch.

Wire A and wire B are now connected in parallel.

(b)

Repeat step (a).[1]

Circuit C

Do not disconnect crocodile clips A or B.

Connect crocodile clip C to a length $l = 95.0\text{ cm}$ of resistance wire C.

It does not matter if the crocodile clips touch.

Wire A, wire B and wire C are now connected in parallel.

(c)

Repeat step (a).[1]

(d)

For each circuit, calculate, and record in Table 2.1, the resistance $R$ of the wire combinations.

Use your values of $V$ and $I$ and the equation:

$$R = \frac{V}{I}$$

[2]

(e)
(i)

Record a resistance $R_A$. $R_A$ is the value of $R$ from Circuit A.

$R_A =$ $\Omega$

Calculate a resistance $R_B$. Use the value of $R$ from Circuit B and the equation:

$$R_B = R \times 2$$

$R_B =$ $\Omega$

Calculate a resistance $R_C$. Use the value of $R$ from Circuit C and the equation:

$$R_C = R \times 3$$

$R_C =$ $\Omega$[2]

(ii)

A student suggests that the values of $R_A$, $R_B$ and $R_C$ should be equal.

State whether your results support this suggestion. Use values from your results to justify your answer.

statement

justification [2]

(f)

Briefly explain why resistor $R_P$, shown in Fig. 2.1, must remain in place throughout the experiment.

[1]

Show the mark scheme

These are the official mark-scheme rows. Each point that matches your answer earns a mark.

Tap the mark scheme to open it full size.

Show a worked answer

How to reach each mark, step by step. Try the question yourself first.

2(a)

  • Read the voltmeter and ammeter with only wire A connected, then open the switch. Record your actual readings in row A.
  • For example, $V = \mathbf{2.4}\,\mathrm{V}$ and $I = \mathbf{0.24}\,\mathrm{A}$. Keep $V$ below $3.0\,\mathrm{V}$ and $I$ below $1.00\,\mathrm{A}$ throughout.

2(b)

  • With wires A and B connected, close the switch and record both meter readings in row B, then open the switch.
  • For example, $V = \mathbf{2.0}\,\mathrm{V}$ and $I = \mathbf{0.40}\,\mathrm{A}$. Record all voltages to the same decimal places and all currents to the same decimal places.

2(c)

  • With all three wires connected, close the switch and record both meter readings in row C, then open the switch.
  • For example, $V = \mathbf{1.8}\,\mathrm{V}$ and $I = \mathbf{0.54}\,\mathrm{A}$. The current increases as more wires are connected in parallel.

2(d)

  • Use $R = V/I$ for each circuit, then give all three answers to the same number of significant figures.
  • For A, $R = 2.4\,\mathrm{V}/0.24\,\mathrm{A} = \mathbf{10}\,\Omega$. For B, $R = 2.0\,\mathrm{V}/0.40\,\mathrm{A} = \mathbf{5.0}\,\Omega$.
  • For circuit C, $R = 1.8\,\mathrm{V}/0.54\,\mathrm{A} = \mathbf{3.3}\,\Omega$. These are example results; use your measured values.

2(e)(i)

  • Use $R_A = R$ for circuit A, $R_B = 2R$ for circuit B and $R_C = 3R$ for circuit C.
  • Using the example resistances, $R_A = \mathbf{10}\,\Omega$ and $R_B = 2(5.0\,\Omega) = \mathbf{10}\,\Omega$.
  • $R_C = 3(3.3\,\Omega) = \mathbf{9.9}\,\Omega$. Use your own results; the three values should be close.

2(e)(ii)

  • For the example results, the suggestion is supported: $10\,\Omega$, $10\,\Omega$ and $9.9\,\Omega$ are within 10\% of each other.
  • Compare your own three values and state whether they agree within experimental accuracy.

2(f)

  • Resistor $R_P$ limits the current, preventing it from exceeding the ammeter range.
Original question

Log in or create account

IGCSE, A-Level & AP