Skip to content

IGCSE Physics · November 2024 · Paper 62 · Difficulty 3 · Standard

Question 1

1

Fig. 1.1 represents a stack of glass microscope slides.

A student takes measurements from a stack of glass microscope slides in order to estimate the number of slides in the stack.

The sides of the stack have been covered with tape so that the student cannot count the number of slides in the stack.

Fig. 1.2 shows side views of the taped stack of slides given to the student. This figure has been drawn at full scale.

(a)

Using Fig. 1.2, measure the length $l$, the width $w$ and the height $h$ of the covered stack of slides in centimetres to the nearest millimetre.

$l =$ cm

$w =$ cm

$h =$ cm[2]

(b)
(i)

The student uses a balance to measure the mass $M$ of the covered stack of slides.

Write down the mass $M$ of the covered slides to the nearest 0.1 g.

$M =$ g[1]

(ii)

Calculate the density $\rho$ of the glass. Use your results from (a) and (b)(i) and the equation shown.

$\rho = \frac{M}{\text{lwh}}$

Give the unit for your answer.

$\rho =$

unit = [2]

(c)

The teacher writes down the mass $m$ and the thickness $t$ of a single microscope slide on a piece of card, as shown in Fig. 1.4.

thickness of a single slide $t = 0.11$ cm

mass of a single slide $m = 4.2$ g

Fig. 1.4

(i)

Use your answer to (b)(i) and information from the card in Fig. 1.4 to estimate the number of microscope slides $N_1$ in the covered stack.

$N_1 =$ [2]

(ii)

Use your answer to (a) and information from the card in Fig. 1.4 to obtain another estimate of the number of microscope slides $N_2$ in the covered stack.

$N_2 =$ [1]

(d)

Two quantities can be considered to be equal within the limits of experimental accuracy if their values are within 10% of each other.

State whether your values of $N_1$ and $N_2$ from (c)(i) and (c)(ii) can be considered equal.

Support your statement with a calculation.

calculation

statement [2]

(e)

Suggest one reason why the estimated values of $N$ are different.

[1]

[Total: 11]

Show the mark scheme

These are the official mark-scheme rows. Each point that matches your answer earns a mark.

Tap the mark scheme to open it full size.

Show a worked answer

How to reach each mark, step by step. Try the question yourself first.

1(a)

  • Measure each side with a ruler and round to the nearest $0.1\,\mathrm{cm}$: $l = \mathbf{7.5}\,\mathrm{cm}$, $w = \mathbf{2.5}\,\mathrm{cm}$ and $h = \mathbf{1.3}\,\mathrm{cm}$.

1(b)(i)

  • The balance reads $57.87\,\mathrm{g}$, which rounds to $\mathbf{57.9}\,\mathrm{g}$.

1(b)(ii)

  • Use $\rho = M/(lwh)$, since the volume of the stack is $lwh$.
  • $\rho = 57.9\,\mathrm{g}/[(7.5\,\mathrm{cm})(2.5\,\mathrm{cm})(1.3\,\mathrm{cm})] = \mathbf{2.3}\,\mathrm{g/cm^3}$.

1(c)(i)

  • Divide the stack mass by the mass of one slide: $N_1 = M/m$.
  • $N_1 = 57.9\,\mathrm{g}/(4.2\,\mathrm{g}) = 13.8$, so the estimate is $\mathbf{14}$ slides.

1(c)(ii)

  • Divide the stack height by one slide thickness: $N_2 = h/t = 1.3\,\mathrm{cm}/(0.11\,\mathrm{cm}) = 11.8$, or $\mathbf{12}$ slides.

1(d)

  • The percentage difference relative to $N_1$ is $|N_1-N_2|/N_1\times 100\% = |14-12|/14\times 100\% = 14.3\%$.
  • This is more than $10\%$, so the estimates are not equal within the stated limit.

1(e)

  • The tape adds to the measured mass, so the number estimated from mass can be $\textbf{too high}$.
Original question

Log in or create account

IGCSE, A-Level & AP