Skip to content

IGCSE Physics · November 2024 · Paper 52 · Difficulty 2 · Core

Question 1

1

In this experiment, you will take measurements of a stack of glass microscope slides to estimate the number of slides in the stack.

Fig. 1.1 shows the stack of slides.

Fig. 1.1
(a)

Measure the length $l$, the width $w$ and the height $h$ of the stack of slides in centimetres to the nearest millimetre.

Do not remove any slides from the stack.

$l = ............$ cm

$w = ............$ cm

$h = ............$ cm[2]

(b)
(i)

Use the balance provided to measure the mass $M$ of the stack of slides to the nearest 0.1 g.

$M = ............$ g[1]

(ii)

Calculate the density $\rho$ of the glass. Use your results from (a) and (b)(i) and the equation shown.

$\rho = \frac{M}{\text{lwh}}$

Give the unit for your answer.

$\rho = ............$

unit = [2]

(c)

The mass $m$ and the thickness $t$ of a single microscope slide are written on the piece of card.

Write down the values of $m$ and $t$ that are on the card.

$m = ............$ g

$t = ............$ cm

(i)

Use your answer to (b)(i) and information from the card in (c) to estimate the number of microscope slides $N_1$ in the stack of slides.

$N_1 = ............$[2]

(ii)

Use your answer to (a) and information from the card in (c) to obtain another estimate of the number of microscope slides $N_2$ in the stack of slides.

$N_2 = ............$[1]

(d)

Two quantities can be considered to be equal within the limits of experimental accuracy if their values are within 10% of each other.

State whether your values of $N_1$ and $N_2$ from (c)(i) and (c)(ii) can be considered equal.

Support your statement with a calculation.

calculation

statement [2]

(e)

Suggest one reason why the estimated values of $N$ may be different.[1]

[Total: 11]

Show the mark scheme

These are the official mark-scheme rows. Each point that matches your answer earns a mark.

Tap the mark scheme to open it full size.

Show a worked answer

How to reach each mark, step by step. Try the question yourself first.

1(a)

  • Measure the stack with a ruler, without removing any slides. Record each length to the nearest $0.1\,\mathrm{cm}$.
  • Typical measurements are $l = \mathbf{7.6}\,\mathrm{cm}$, $w = \mathbf{2.5}\,\mathrm{cm}$ and $h = \mathbf{1.2}\,\mathrm{cm}$; use your own measurements.

1(b)(i)

  • Put the whole stack on the balance and record $M$ to the nearest $0.1\,\mathrm{g}$. The reading depends on your stack.

1(b)(ii)

  • Use $\rho = M/(lwh)$: multiply your three measured lengths to find the volume, then divide the measured mass by it.
  • With $M$ in $\mathrm{g}$ and each length in $\mathrm{cm}$, $\rho = \mathbf{M/(lwh)}\,\mathrm{g/cm^3}$.

1(c)(i)

  • Use $N_1 = M/m$: divide the mass of the whole stack by the mass of one slide from the card.
  • Round to the nearest whole slide: $N_1 = \mathbf{\operatorname{round}(M/m)}$.

1(c)(ii)

  • Use $N_2 = h/t$: divide the height of the stack by the thickness of one slide from the card, using the same units.
  • Your estimate is $N_2 = \mathbf{h/t}$ slides.

1(d)

  • Find the percentage difference using $\lvert N_1-N_2\rvert/N_1\times 100\%$.
  • If this is at most $10\%$, the estimates can be considered equal; if it is greater, they cannot. Use your own values to decide.

1(e)

  • The tape adds mass to the stack. Dividing this total mass by the mass of one slide can therefore overestimate the number of slides.
Original question

Log in or create account

IGCSE, A-Level & AP