Skip to content

IGCSE Physics · November 2022 · Paper 53 · Difficulty 3 · Standard

Question 3

3

In this experiment, you will investigate circuits containing resistors in parallel.

The first circuit has been set up for you.

Carry out the following instructions, referring to Fig. 3.1.

All numeric answers must have appropriate units.

(a)
(i)

Close the switch.

Measure the potential difference (p.d.) $V$ across the parallel combination of resistors P and Q.

$V =$

Measure the current $I_T$ in the circuit.

$I_T =$ [2]

Open the switch.

(ii)

Calculate the resistance $R_{PQ}$ of the parallel combination of resistors P and Q.

Use your readings from (a)(i) and the equation $R_{PQ} = \frac{V}{I_T}$.

$R_{PQ} =$ [1]

(iii)

Disconnect the voltmeter and reconnect it to measure the potential difference across resistor S.

Close the switch.

Measure the potential difference $V_S$ across resistor S.

$V_S =$

Open the switch.

Disconnect the voltmeter from the circuit.

Calculate the resistance $R_S$ of resistor S.

Use your readings from (a)(i), (a)(iii) and the equation $R_S = \frac{V_S}{I_T}$.

$R_S =$ [2]

(b)

Disconnect the ammeter and reconnect it as shown in Fig. 3.2.

Close the switch.

Measure the current $I_P$ in resistor P.

$I_P =$ [1]

Open the switch.

(c)

Disconnect the ammeter and reconnect it as shown in Fig. 3.3.

Close the switch.

Measure the current $I_Q$ in resistor Q.

$I_Q =$ [2]

Open the switch.

(d)

A student suggests that $I_T$ should be equal to $I_P + I_Q$.

State whether your results support this suggestion. Justify your statement by reference to values from your results.

statement

justification

[1]

(e)
(i)

A student changes the circuit and uses a variable resistor to control the current in the circuit.

In the space provided, draw the circuit symbol for a variable resistor.

Mark with an X on Fig. 3.3 where a variable resistor is connected to control the current in resistor S without affecting the resistance of either of the parallel branches.[1]

(ii)

The current in the circuit can be controlled by connecting a range of different resistors in place of resistors P and Q.

State one disadvantage of this method instead of using a variable resistor to control the current.

[1]

[Total: 11]

Show the mark scheme

These are the official mark-scheme rows. Each point that matches your answer earns a mark.

Tap the mark scheme to open it full size.

Show a worked answer

How to reach each mark, step by step. Try the question yourself first.

3(a)(i)

  • Read the voltmeter across P and Q and record $V$ in volts, to at least one decimal place.
  • Read the ammeter and record $I_T$ in amps, to at least two decimal places. The actual readings depend on your circuit.

3(a)(ii)

  • Use $R_{PQ} = V/I_T$.
  • For example, if $V = 1.0\,\mathrm{V}$ and $I_T = 0.20\,\mathrm{A}$, then $R_{PQ} = 1.0\,\mathrm{V}/(0.20\,\mathrm{A}) = \mathbf{5.0}\,\mathrm{\Omega}$. Use your own readings.

3(a)(iii)

  • Connect the voltmeter across S and measure $V_S$; it should be greater than $V$ across P and Q.
  • Use $R_S = V_S/I_T$.
  • For example, if $V_S = 1.5\,\mathrm{V}$ and $I_T = 0.20\,\mathrm{A}$, then $R_S = 1.5\,\mathrm{V}/(0.20\,\mathrm{A}) = \mathbf{7.5}\,\mathrm{\Omega}$. Use your own readings.

3(b)

  • Read $I_P$ from the ammeter in the P branch and record it in amps. It should be less than $I_T$ because some current flows through Q.

3(c)

  • Read $I_Q$ from the ammeter in the Q branch and record it in amps.
  • Check that $I_P + I_Q$ is within $10\%$ of $I_T$. Use amps for currents, volts for p.d.s and ohms for resistances.

3(d)

  • Add $I_P$ and $I_Q$ and compare the sum with $I_T$. Allow for experimental uncertainty.
  • For example, $0.10\,\mathrm{A} + 0.10\,\mathrm{A} = 0.20\,\mathrm{A}$, which matches an $I_T$ of $0.20\,\mathrm{A}$, so these results support the suggestion. Use your own values.

3(e)(i)

  • Draw a resistor rectangle with a diagonal arrow through it. Mark X in the series part of the circuit, so the variable resistor is not in either parallel branch.

3(e)(ii)

  • Changing fixed resistors does not give a continuous range of current values.
Original question

Log in or create account

IGCSE, A-Level & AP