Skip to content

IGCSE Physics · November 2021 · Paper 51 · Difficulty 4 · Challenging

Question 2

2

In this experiment, you will investigate the resistance of combinations of resistors.

Fig. 2.1 shows the first circuit arrangement. The circuit is set up for you.

Fig. 2.1
(a)

Switch on.

(i)

Record $V_X$, the potential difference (p.d.) across resistor X.

$V_X$ = [1]

(ii)

Record $I_X$, the current in the circuit and then switch off the power supply.

$I_X$ = [1]

(iii)

Calculate $R_X$, the resistance of resistor X, using the equation $R_X = \frac{V_X}{I_X}$.

$R_X$ = [1]

(b)

Disconnect the voltmeter.

Reconnect the voltmeter to measure $V_{XY}$, the potential difference across the two resistors X and Y in series.

Switch on.

(i)

Record $V_{XY}$.

$V_{XY}$ =

Record $I_{XY}$, the current in the circuit and then switch off the power supply.

$I_{XY}$ = [1]

(ii)

Calculate $R_{XY}$, the combined resistance of resistors X and Y connected in series, using the equation $R_{XY} = \frac{V_{XY}}{I_{XY}}$.

$R_{XY}$ = [1]

(c)

Disconnect the voltmeter.

Connect resistor Z in parallel with resistor X.

Connect the voltmeter to measure $V_{XZ}$, the potential difference across the parallel combination of resistor X and resistor Z.

(i)

Draw the circuit diagram for this arrangement. Label the resistors X, Y and Z.[2]

(ii)

Switch on.

Record $V_{XZ}$, the potential difference across the two resistors X and Z in parallel.

$V_{XZ}$ =

Record $I_{XZ}$, the current in the circuit and then switch off the power supply.

$I_{XZ}$ = [1]

(iii)

Calculate $R_{XZ}$, the combined resistance of resistors X and Z connected in parallel, using the equation $R_{XZ} = \frac{V_{XZ}}{I_{XZ}}$.

$R_{XZ}$ = [1]

(d)

A student does this experiment using a set of three identical resistors. Her results show that, within the limits of experimental accuracy, the combined resistance of two identical resistors connected in series is four times the combined resistance of the same two resistors connected in parallel. To test whether her results are true for other values of resistance, she does the same procedure with other sets of three identical resistors.

Suggest the values of resistance she could use to reach a conclusion during a 1 hour practical lesson.

[2]

Show the mark scheme

These are the official mark-scheme rows. Each point that matches your answer earns a mark.

Tap the mark scheme to open it full size.

Show a worked answer

How to reach each mark, step by step. Try the question yourself first.

2(a)(i)

  • $V_X$ is the voltmeter reading across resistor X. Record it in $\mathrm{V}$ to at least one decimal place; the expected reading is below $3\,\mathrm{V}$.
  • The circuit diagram shows the meter connection, but no meter reading. Use the reading from your apparatus.

2(a)(ii)

  • $I_X$ is the ammeter reading, since the same current passes through X and Y in series. Record it in $\mathrm{A}$ to at least two decimal places; the expected reading is below $1\,\mathrm{A}$.
  • Use the reading from your apparatus, then switch off to reduce heating of the resistors. No numerical meter reading is shown.

2(a)(iii)

  • Use resistance $R = V/I$. Divide the measured voltage across X by the measured current through X.
  • The result is $R_X = \mathbf{\tfrac{V_X}{I_X}}$. Use volts and amperes to obtain resistance in $\mathrm{\Omega}$. A numerical answer needs your readings from (a)(i) and (a)(ii).

2(b)(i)

  • $V_{XY}$ is the voltmeter reading across both resistors. It is greater than $V_X$ because it includes the voltage across Y as well. Record it in $\mathrm{V}$.
  • $I_{XY}$ is the ammeter reading, in $\mathrm{A}$. It should be close to $I_X$, since moving the voltmeter does not change the resistors in series. Record both readings from your apparatus, then switch off.

2(b)(ii)

  • Use resistance $R = V/I$. Divide the voltage across the series pair by the current through the pair.
  • The result is $R_{XY} = \mathbf{\tfrac{V_{XY}}{I_{XY}}}$. Use the readings from (b)(i), with voltage in $\mathrm{V}$ and current in $\mathrm{A}$, to obtain resistance in $\mathrm{\Omega}$.

2(c)(i)

  • Draw resistors X and Z in parallel, with their ends joined to the same two junctions.
  • Connect Y, the ammeter and the supply in series with that parallel pair. Connect the voltmeter across X and Z.

2(c)(ii)

  • $V_{XZ}$ is the voltmeter reading across the parallel pair. Record it in $\mathrm{V}$. It should be less than $V_X$: adding Z lowers the resistance of this section, so it takes a smaller share of the supply voltage.
  • $I_{XZ}$ is the ammeter reading for the whole circuit, in $\mathrm{A}$. Use your apparatus readings, then switch off. The current through X alone must not be used for the combined resistance.

2(c)(iii)

  • Use resistance $R = V/I$: $R_{XZ} = \mathbf{\tfrac{V_{XZ}}{I_{XZ}}}$. Divide the readings from (c)(ii), using volts and amperes, to obtain resistance in $\mathrm{\Omega}$.
  • For equal resistors X and Z, $1/R_{XZ} = 1/R_X + 1/R_X$, so the expected result is $R_{XZ} \approx \mathbf{\tfrac{R_X}{2}}$. Two equal parallel paths halve the resistance; allow for measurement uncertainty.

2(d)

  • Try four more sets with resistances of $\mathbf{2}$, $\mathbf{5}$, $\mathbf{10}$ and $\mathbf{20}\,\mathrm{\Omega}$ per resistor.
  • Use three identical resistors within each set, so only the resistance changes between sets.
Original question

Log in or create account

IGCSE, A-Level & AP