Skip to content

IGCSE Physics · November 2020 · Paper 52 · Difficulty 3 · Standard

Question 3

3

In this experiment, you will investigate the resistance of samples of resistance wire.

Carry out the following instructions, referring to Fig. 3.1.

The circuit shown in Fig. 3.1 has been provided for you.

Table 3.1 shows how the samples of wire are connected into the circuit.

Table 3.1

sectionresistance wire
BCone 30 cm piece
CDtwo 30 cm pieces
DEthree 30 cm pieces
(a)
(i)

● Switch on.

  • Measure the current $I$ in the circuit.

$I$ = [1]

(ii)

Connect the voltmeter across section BC of the resistance wire.

Measure and record the potential difference (p.d.) $V_1$ across section BC. Switch off.

$V_1$ = [1]

Calculate the resistance $R_1$ of section BC using the equation $R_1 = \frac{V_1}{I}$.

Give your answer to a suitable number of significant figures for this experiment and include the unit.

$R_1$ = [1]

(iii)

Disconnect the voltmeter and its leads from section BC. Connect the voltmeter across section CD. Switch on.

Measure and record the potential difference (p.d.) $V_2$ across section CD. Switch off.

$V_2$ =

Calculate the resistance $R_2$ of section CD using the equation $R_2 = \frac{V_2}{I}$. Give your answer to a suitable number of significant figures for this experiment and include the unit.

$R_2$ = [1]

(iv)

Disconnect the voltmeter and its leads from section CD. Connect the voltmeter across section DE. Switch on.

Measure and record the potential difference (p.d.) $V_3$ across section DE. Switch off.

$V_3$ =

Calculate the resistance $R_3$ of section DE using the equation $R_3 = \frac{V_3}{I}$. Give your answer to a suitable number of significant figures for this experiment and include the unit.

$R_3$ = [3]

(b)
(i)

The sections BC, CD and DE are all the same length and made of the same metal.

Tick the box to show your conclusion from the results.

The resistance of a section increases as the number of wires increases

The resistance of a section decreases as the number of wires increases

The resistance of a section is independent of the number of wires.[1]

(ii)

Justify your conclusion in (b)(i) by reference to your results.

[1]

(c)

Explain how you would change this experiment to investigate the relationship between the length of a sample of wire and its resistance.

[2]

Show the mark scheme

These are the official mark-scheme rows. Each point that matches your answer earns a mark.

Tap the mark scheme to open it full size.

Show a worked answer

How to reach each mark, step by step. Try the question yourself first.

3(a)(i)

  • Close the switch and read the ammeter. Record $I$ in $\mathrm{A}$ to at least two decimal places; the current should be below $1\,\mathrm{A}$.
  • Fig. 3.1 shows an ammeter symbol, not a meter reading. You must use the reading from the apparatus.

3(a)(ii)

  • Connect the voltmeter in parallel across B and C. Record $V_1$ in $\mathrm{V}$ to at least one decimal place, then switch off. It should be below $3\,\mathrm{V}$.
  • Use $R_1 = V_1/I$. Divide your measured voltage in $\mathrm{V}$ by your measured current in $\mathrm{A}$; record the result in $\Omega$, to two or three significant figures.
  • The paper supplies no meter readings, so the numerical resistance depends on your measurements.

3(a)(iii)

  • Connect the voltmeter in parallel across C and D. Switch on, record $V_2$ in $\mathrm{V}$, then switch off.
  • Use $R_2 = V_2/I$. Divide your measured $V_2$ in $\mathrm{V}$ by $I$ in $\mathrm{A}$ and record the resistance in $\Omega$, to two or three significant figures.
  • Two identical wires in parallel should give about half the resistance of BC. A numerical result needs the meter readings.

3(a)(iv)

  • Measure $V_3$ across D and E in $\mathrm{V}$, then switch off. Use $R_3 = V_3/I$, with your voltage in $\mathrm{V}$ and current in $\mathrm{A}$.
  • Record the calculated resistance in $\Omega$ to two or three significant figures. A numerical result needs your meter readings.
  • Three identical wires are in parallel, so expect $R_1 \approx 3R_3$. Your results should agree with this within about $10\%$.

3(b)(i)

  • The resistance of a section decreases as the number of wires increases. The wires are connected in parallel, giving more paths for current.

3(b)(ii)

  • Use your calculated resistances to check whether $R_1 \approx 2R_2$ and $R_1 \approx 3R_3$. Quote your values, with units, to support the comparison.
  • These ratios support the conclusion that more parallel wires give a lower resistance: two wires give about half, and three about one-third, of the resistance of one wire.

3(c)

  • Use different lengths of the same wire, keeping the material and thickness the same.
  • Measure the potential difference and current for each length, then use $R = V/I$ to find each resistance.
Original question

Log in or create account

IGCSE, A-Level & AP