Skip to content

IGCSE Physics · June 2025 · Paper 53 · Difficulty 3 · Standard

Question 3

3

In this experiment, you will investigate circuits containing different combinations of resistors.

Circuit A has been set up for you.

Refer to Fig. 3.1.

Resistor $R_P$ must remain in place throughout the experiment.

Circuit A

(a)
(i)

Close the switch.

Measure, and record in Table 3.1:

  • the potential difference (p.d.) $V$ across terminals P and Q
  • the current $I$ in the circuit.

Open the switch.

V/VI /AR/Ω
circuit A
circuit B
circuit C

[2]

(ii)

Calculate, and record in Table 3.1, resistance $R$. Use your values of $V$ and $I$ and the equation $R = \frac{V}{I}$.[1]

Circuit B

(b)

Disconnect $R_2$ from circuit A. Resistor $R_1$ remains connected between terminals P and Q, as shown in Fig. 3.2.

Repeat the procedures in (a)(i) and (a)(ii).[1]

Circuit C

(c)

Connect $R_2$ in series with $R_1$ between terminals P and Q, as shown in Fig. 3.3.

Repeat the procedures in (a)(i) and (a)(ii).[1]

(d)
(i)

Calculate resistance $R_A$. Use the value of $R$ from circuit A and the equation:

$R_A = 2R$.

$R_A =$ $\Omega$

Record resistance $R_B$. $R_B$ is equal to the value of $R$ from circuit B.

$R_B =$ $\Omega$

Calculate resistance $R_C$. Use the value of $R$ from circuit C and the equation:

$R_C = \frac{R}{2}$.

$R_C =$ $\Omega$[2]

(ii)

A student suggests that $R_A$, $R_B$ and $R_C$ should all be equal.

State whether your results support this suggestion. Justify your statement with reference to values from your results.

statement

justification [2]

(e)

Briefly explain why resistor $R_P$, shown in Fig. 3.1, must remain in place throughout the experiment.

$R_P$ has a resistance of $3\Omega$. Use your values in Table 3.1 to support your answer.[1]

(f)

A student determines the resistance of $R_1$. He uses a variable resistor in circuit B to control the current and draws a graph of $V$ against $I$.

Briefly explain one advantage of using a variable resistor to control the current.[1]

Show the mark scheme

These are the official mark-scheme rows. Each point that matches your answer earns a mark.

Tap the mark scheme to open it full size.

Show a worked answer

How to reach each mark, step by step. Try the question yourself first.

3(a)(i)

  • With the switch closed, read $V$ across P and Q and $I$ in the circuit. Record both in the circuit A row, then open the switch.
  • The readings depend on your apparatus; expect $V < 3.0\,\mathrm{V}$ and $I < 1.00\,\mathrm{A}$. The current should decrease from circuit A to B to C.

3(a)(ii)

  • Use $R = V/I$ for circuit A.
  • For example, if $V = 2.0\,\mathrm{V}$ and $I = 0.40\,\mathrm{A}$, then $R = (2.0\,\mathrm{V})/(0.40\,\mathrm{A}) = \mathbf{5.0}\,\mathrm{\Omega}$. Record your result in the table.

3(b)

  • With only $R_1$ between P and Q, measure $V$ and $I$ for circuit B. Open the switch after taking the readings.
  • Use $R = V/I$ to find the resistance and record it. It should be greater than the resistance for circuit A.

3(c)

  • With $R_1$ and $R_2$ in series, measure $V$ and $I$ for circuit C. Open the switch after taking the readings.
  • Use $R = V/I$ to find $R$ and record it to the same two or three significant figures as the other resistances. It should be greater than for circuit B.

3(d)(i)

  • Use $R_A = 2R$ for circuit A. For example, with $R = 5.0\,\mathrm{\Omega}$, $R_A = 2(5.0\,\mathrm{\Omega}) = \mathbf{10}\,\mathrm{\Omega}$.
  • Take $R_B$ from circuit B. For example, $R_B = \mathbf{10}\,\mathrm{\Omega}$.
  • Use $R_C = R/2$ for circuit C. For example, with $R = 20\,\mathrm{\Omega}$, $R_C = (20\,\mathrm{\Omega})/2 = \mathbf{10}\,\mathrm{\Omega}$. Use your own table values.

3(d)(ii)

  • If your three values are close, say yes: they are equal within experimental accuracy. Quote your values of $R_A$, $R_B$ and $R_C$ to support this.
  • If the values differ by more than the expected experimental uncertainty, say no and quote your values to show the difference.

3(e)

  • $R_P$ limits the current, helping to stop it exceeding the ammeter range. Use your table values to show that the current rises as resistance falls.

3(f)

  • A variable resistor makes it easy to obtain several different readings of current and potential difference for the graph.
Original question

Log in or create account

IGCSE, A-Level & AP