Skip to content

IGCSE Physics · June 2024 · Paper 53 · Difficulty 2 · Core

Question 1

1

In this experiment, you will determine the density of modelling clay by two methods.

Refer to Fig. 1.1.

Method 1

(a)
(i)

Measure the length $l$, width $w$ and height $h$ of block A. Record your values in centimetres to the nearest millimetre.

$l$ = cm

$w$ = cm

$h$ = cm[1]

(ii)

Calculate the volume $V_A$ of block A. Use your measurements from (a)(i) and the equation $V_A = l \times w \times h$.

$V_A$ = cm$^3$[1]

(b)

Suggest a possible source of inaccuracy in measuring the dimensions of the block.

Describe how the accuracy of these measurements can be improved.

You are not required to do this improved investigation.

suggestion

improvement

[2]

(c)

Measure the mass $m_A$ of block A. Use the top-pan balance.

$m_A$ = g[1]

(d)

Calculate a value $\rho_A$ for the density of the modelling clay. Use your results from (a)(ii) and (c) and the equation $\rho_A = \frac{m_A}{V_A}$. Include the unit for the density.

$\rho_A$ = [2]

Method 2

(e)

Measure the weight $W_B$ of block B, as shown in Fig. 1.2.

$W_B$ = N[1]

(f)
(i)

Pour approximately 60 cm$^3$ of water into the measuring cylinder.

Measure and record the actual volume $V_1$ of the water in the measuring cylinder.

$V_1$ = cm$^3$

Remove the loop of thread from the force meter and lower block B carefully into the water in the measuring cylinder, as shown in Fig. 1.3.

Measure and record the new reading $V_2$ of the measuring cylinder.

$V_2$ = cm$^3$[1]

(ii)

Draw an arrow on Fig. 1.4 to show the correct line of sight to obtain the value for the volume of water in the measuring cylinder.

[1]

(g)

Calculate another value $\rho_B$ for the density of modelling clay. Use your readings from (e) and (f) and the equation $\rho_B = \frac{W_B \times k}{(V_2 - V_1)}$, where $k = 100 \text{ g/N}$.

$\rho_B$ = [1]

[Total: 11]

Show the mark scheme

These are the official mark-scheme rows. Each point that matches your answer earns a mark.

Tap the mark scheme to open it full size.

Show a worked answer

How to reach each mark, step by step. Try the question yourself first.

1(a)(i)

  • Measure the actual block with a ruler; the sketch does not give its dimensions. Record each measurement to the nearest $0.1\,\mathrm{cm}$.
  • For example, measurements could be $l = \mathbf{4.0}\,\mathrm{cm}$, $w = \mathbf{4.0}\,\mathrm{cm}$ and $h = \mathbf{3.0}\,\mathrm{cm}$.

1(a)(ii)

  • Use $V_A = lwh$ with your measurements.
  • For example, $V_A = (4.0\,\mathrm{cm})(4.0\,\mathrm{cm})(3.0\,\mathrm{cm}) = \mathbf{48}\,\mathrm{cm^3}$.

1(b)

  • The block may have uneven sides, so a single measurement may not represent the whole block.
  • Measure each dimension in several places and take the average for each dimension.

1(c)

  • Zero the top-pan balance, then place block A on it and read its mass. The sketch does not give the mass.
  • For example, the balance might read $m_A = \mathbf{72}\,\mathrm{g}$; use your own reading.

1(d)

  • Use $\rho_A = m_A/V_A$ with your mass and volume.
  • For example, $\rho_A = 72\,\mathrm{g}/(48\,\mathrm{cm^3}) = \mathbf{1.5}\,\mathrm{g/cm^3}$.

1(e)

  • Read the force meter with block B hanging still. Fig. 1.2 has no numbered scale, so it does not give a numerical reading.
  • For example, the reading might be $W_B = \mathbf{0.48}\,\mathrm{N}$; use your own reading.

1(f)(i)

  • Read the bottom of the meniscus at eye level before and after putting block B fully under the water.
  • For example, $V_1 = \mathbf{60}\,\mathrm{cm^3}$ and $V_2 = \mathbf{92}\,\mathrm{cm^3}$. The second reading is higher because the block displaces water.

1(f)(ii)

  • Draw a horizontal arrow towards the bottom of the meniscus. Your eye must be at this level to avoid parallax.
Worked answer drawing

1(g)

  • Use $\rho_B = W_Bk/(V_2-V_1)$ with your readings. The difference in volumes is the volume of block B.
  • For example, $\rho_B = (0.48\,\mathrm{N})(100\,\mathrm{g/N})/(92-60)\,\mathrm{cm^3} = \mathbf{1.5}\,\mathrm{g/cm^3}$.
Original question

Log in or create account

IGCSE, A-Level & AP