Skip to content

IGCSE Physics · June 2021 · Paper 62 · Difficulty 3 · Standard

Question 3

3

A student investigates resistance.

Fig. 3.1 shows the circuit used.

(a)

The student measures the current $I$ in the circuit.

He places the sliding contact S at C and measures the potential difference (p.d.) $V_1$ across the resistor R.

The voltmeter and ammeter are shown in Fig. 3.2 and Fig. 3.3.

(i)

Write down the readings.

Include the units for potential difference, current or resistance where appropriate in all parts of the question.

$V_1$ =

$I_1$ = [2]

(ii)

Calculate the resistance $R_1$ of the resistor using the equation $R_1 = \frac{V_1}{I_1}$.

$R_1$ = [2]

(b)

The student disconnects the voltmeter from terminal B and connects the voltmeter to terminal C.

He places the sliding contact S at a distance $l$ = 20.0 cm from C. He records, in Table 3.1, the reading on the voltmeter.

He repeats the procedure using $l$ = 40.0 cm, 60.0 cm, 80.0 cm and 100.0 cm. His readings are shown in Table 3.1.

Table 3.1

$l$ / cm$V$ / V
20.00.4
40.00.8
60.01.1
80.01.5
100.01.9

Plot a graph of $V$ / V ($y$-axis) against $l$ / cm ($x$-axis). Start both axes at the origin (0,0).

[4]

(c)

Use your value of $V_1$ from (a)(i) to find the length $l_R$ of resistance wire that has the same resistance as resistor R. Show clearly on the graph how you obtained the necessary information.

$l_R$ = cm[2]

(d)

The resistance of the resistance wire is proportional to its length. Estimate the resistance of 100 cm of the resistance wire.

estimate [1]

[Total: 11]

Show the mark scheme

These are the official mark-scheme rows. Each point that matches your answer earns a mark.

Tap the mark scheme to open it full size.

Show a worked answer

How to reach each mark, step by step. Try the question yourself first.

3(a)(i)

  • Read the voltmeter and ammeter scales: $V_1 = \mathbf{0.60}\,\mathrm{V}$ and $I_1 = \mathbf{0.32}\,\mathrm{A}$.

3(a)(ii)

  • Use $R_1 = V_1/I_1$.
  • $R_1 = 0.60\,\mathrm{V}/0.32\,\mathrm{A} = \mathbf{1.875}\,\mathrm{\Omega}$.

3(b)

  • Label the horizontal axis $l/\mathrm{cm}$ and the vertical axis $V/\mathrm{V}$. Start both at zero and choose scales that use the grid well.
  • Plot $(20.0, 0.4)$, $(40.0, 0.8)$, $(60.0, 1.1)$, $(80.0, 1.5)$ and $(100.0, 1.9)$.
  • Draw a thin, continuous best-fit straight line with points balanced above and below it. It need not pass through every point.

3(c)

  • From $0.60\,\mathrm{V}$ on the vertical axis, draw across to the best-fit line and then down to the length axis.
  • Read approximately $l_R = \mathbf{32}\,\mathrm{cm}$; the value depends on your line.

3(d)

  • Use $R = V/I$ for the $100\,\mathrm{cm}$ wire, taking the current as $0.32\,\mathrm{A}$.
  • $R = 1.9\,\mathrm{V}/0.32\,\mathrm{A} = \mathbf{5.9}\,\mathrm{\Omega}$.
Original question

Log in or create account

IGCSE, A-Level & AP