Skip to content

IGCSE Physics · June 2020 · Paper 63 · Difficulty 3 · Standard

Question 2

2

Some students investigate a circuit containing different combinations of resistors. Part of the circuit they are using is shown in Fig. 2.1.

(a)
(i)

On Fig. 2.1, complete the circuit to show:

  • an ammeter connected to measure the current in the circuit
  • a voltmeter connected to measure the potential difference (p.d.) across terminals P and Q. [2]

(ii)

A student measures the potential difference $V_1$ across terminals P and Q and the current $I_1$ in the circuit.

Read the values of $V_1$ and $I_1$ shown on the meters in Fig. 2.2 and Fig. 2.3.

$V_1 =$ V

$I_1 =$ A[2]

(iii)

Calculate a resistance $R_1$ using your values from (a)(ii) and the equation $R_1 = \frac{V_1}{I_1}$.

$R_1 =$ [1]

(b)

The student connects two resistors in series between terminals P and Q, as shown in Fig. 2.4.

Fig. 2.4

He measures the potential difference $V_2$ across terminals P and Q and the current $I_2$ in the circuit.

$V_2 =$ 2.7 V

$I_2 =$ 0.26 A

Calculate a resistance $R_2$ using these values and the equation $R_2 = \frac{V_2}{(I_2 \times 2)}$.

$R_2 =$ [1]

(c)

The student connects the two resistors in parallel between terminals P and Q, as shown in Fig. 2.5.

He measures the potential difference $V_3$ across terminals P and Q and the current $I_3$ in the circuit.

$V_3 =$ 2.3 V

$I_3 =$ 0.94 A

Calculate a resistance $R_3$ using these values and the equation $R_3 = \frac{(V_3 \times 2)}{I_3}$.

$R_3 =$ [1]

(d)

Another student suggests that $R_1$, $R_2$ and $R_3$ should be equal. State whether your results support this suggestion. Justify your statement with reference to your results.

statement

justification [2]

(e)
(i)

A student wants to determine $R_1$ by using a potential divider to vary the potential difference in the circuit. Draw the symbol for a potential divider.[1]

(ii)

Briefly explain how the use of a potential divider may give a more reliable value for $R_1$ than using the procedure carried out in (a).

[1]

[Total: 11]

Show the mark scheme

These are the official mark-scheme rows. Each point that matches your answer earns a mark.

Tap the mark scheme to open it full size.

Show a worked answer

How to reach each mark, step by step. Try the question yourself first.

2(a)(i)

  • Draw an ammeter symbol in series with the circuit and a voltmeter symbol connected in parallel across P and Q.

2(a)(ii)

  • The meters read $V_1 = \mathbf{2.4}\,\mathrm{V}$ and $I_1 = \mathbf{0.48}\,\mathrm{A}$.

2(a)(iii)

  • Use $R_1 = V_1/I_1$.
  • $R_1 = 2.4\,\mathrm{V}/0.48\,\mathrm{A} = \mathbf{5.0}\,\Omega$.

2(b)

  • Use $R_2 = V_2/(2I_2)$.
  • $R_2 = 2.7\,\mathrm{V}/(2\times0.26\,\mathrm{A}) = \mathbf{5.2}\,\Omega$.

2(c)

  • Use $R_3 = 2V_3/I_3$.
  • $R_3 = 2(2.3\,\mathrm{V})/0.94\,\mathrm{A} = \mathbf{4.9}\,\Omega$.

2(d)

  • Yes, within experimental accuracy: $5.0\,\Omega$, $5.2\,\Omega$ and $4.9\,\Omega$ are close together.

2(e)(i)

  • Draw a resistor with a terminal at each end and a third terminal connected to an arrow touching its middle. The arrow represents the sliding contact.

2(e)(ii)

  • Take several pairs of voltage and current readings at different settings and use them to find an average resistance.
Original question

Log in or create account

IGCSE, A-Level & AP