Skip to content

IGCSE Physics · June 2020 · Paper 63 · Difficulty 3 · Standard

Question 1

1

A student determines the weight of a metre rule.

She uses the apparatus shown in Fig. 1.1.

The metre rule is supported by a pivot at the 10.0 cm mark and is suspended from a forcemeter by a loop of thread at the 90.0 cm mark.

(a)

The student places a 2.0 N weight at a distance $l$ from the pivot.

She then adjusts the height of the clamp holding the pivot so that the metre rule is horizontal.

She reads the force $F$ on the forcemeter.

Fig. 1.2 shows the weight and the metre rule from above.

Fig. 1.3 shows the reading on the forcemeter.

Fig. 1.2 (not to scale)
(i)

Calculate the value of $l$ from readings taken from Fig. 1.2.

Show your working clearly.

$l$ = cm[2]

(ii)

Read the value $F$ shown on the forcemeter in Fig. 1.3.

$F$ = N[1]

(iii)

Explain how the student makes sure that the rule is horizontal before taking the reading.

You may draw a diagram.

[1]

(b)

The student carries out the procedure for values of $l$ = 20.0 cm, 30.0 cm, 40.0 cm, 50.0 cm and 60.0 cm. Her readings are shown in Table 1.1.

$l$/cm$F$/N
20.01.35
30.01.60
40.01.90
50.02.15
60.02.45

Plot a graph of $F$/N ($y$-axis) against $l$/cm ($x$-axis).

Start your axes from the origin (0,0).[4]

(c)
(i)

From your graph determine $F_0$, the value of $F$ when $l$ = 0.

$F_0$ = N[1]

(ii)

Calculate the weight $W_R$ of the metre rule, using the equation $W_R$ = 2 × $F_0$.

$W_R$ = N[1]

(d)

Another student carrying out this experiment finds it difficult to be sure that he has placed the centre of the 2.0 N weight on the metre rule at the correct value of $l$.

Suggest a more precise method of applying a 2.0 N load to the metre rule in this experiment.

Explain why this method is an improvement.

[1]

[Total: 11]

Show the mark scheme

These are the official mark-scheme rows. Each point that matches your answer earns a mark.

Tap the mark scheme to open it full size.

Show a worked answer

How to reach each mark, step by step. Try the question yourself first.

1(a)(i)

  • Use $l = x_{\mathrm{load}} - x_{\mathrm{pivot}}$, where each $x$ is a position on the rule.
  • The centre of the weight is at $25.0\,\mathrm{cm}$ and the pivot is at $10.0\,\mathrm{cm}$.
  • $l = 25.0\,\mathrm{cm} - 10.0\,\mathrm{cm} = \mathbf{15.0}\,\mathrm{cm}$.

1(a)(ii)

  • The forcemeter reads $\mathbf{1.3}\,\mathrm{N}$.

1(a)(iii)

  • Measure the height of each end above the bench and adjust the rule until the heights are equal.

1(b)

  • Put $l/\mathrm{cm}$ on the horizontal axis and $F/\mathrm{N}$ on the vertical axis. Start both at zero and use scales that fill at least half the grid.
  • Plot $(20.0,1.35)$, $(30.0,1.60)$, $(40.0,1.90)$, $(50.0,2.15)$ and $(60.0,2.45)$. Draw a thin best-fit line and extend it to the vertical axis.

1(c)(i)

  • Read where the best-fit line meets the vertical axis: approximately $F_0 = \mathbf{0.80}\,\mathrm{N}$. Your value depends on your line.

1(c)(ii)

  • Use $F_W = 2F_0$ for the weight of the rule.
  • $F_W = 2(0.80\,\mathrm{N}) = \mathbf{1.6}\,\mathrm{N}$. Use your own graph intercept.

1(d)

  • Hang the load from a thin cotton loop around the rule. The loop can be placed more precisely on the required mark.
Original question

Log in or create account

IGCSE, A-Level & AP