Skip to content

IGCSE Physics · March 2024 · Paper 52 · Difficulty 3 · Standard

Question 3

3

In this experiment, you will determine the focal length of a converging lens by two methods.

Refer to Fig. 3.1.

(a)

Set up the apparatus as shown in Fig. 3.1.

Set the distance $u$ between the illuminated object and the lens to 20.0 cm.

Switch on the lamp.

Place the screen near the lens. Move the screen until a sharp image of the illuminated object is seen on the screen.

(i)

Describe a technique for obtaining an image that is as sharp as possible.[1]

(ii)

Measure $v$, the distance from the lens to the screen as indicated in Fig. 3.1.

$v$ = cm

Measure $h_O$, the height of the illuminated object, indicated in Fig. 3.1.

$h_O$ = cm

Measure $h_I$, the height of the image on the screen.

$h_I$ = cm[2]

Switch off the lamp.

(iii)

Calculate a value $M$ for the magnification, using the equation $M = \frac{h_I}{h_O}$.

$M$ = [1]

(b)

Calculate a value $f_1$ for the focal length of the lens. Use your values from (a)(ii) and (a)(iii) and the equation $f_1 = \frac{v}{(M + 1)}$.

Give an appropriate unit.

$f_1$ = [2]

(c)

Describe one difficulty that is experienced when using a ruler to measure the height of the image. Suggest an improvement to the apparatus to overcome this.

You are not required to do an experiment with this improved apparatus.

difficulty

improvement [2]

(d)

Adjust the position of the lens so that $u = 40.0$ cm.

Switch on the lamp.

Place the screen near the lens. Move the screen until a sharp image of the illuminated object is seen on the screen.

Measure the distance $v$ between the lens and the screen as indicated in Fig. 3.1.

$v$ = cm[1]

Switch off the lamp.

(e)

Calculate a second value $f_2$ for the focal length of the lens. Use your values from (d) and the equation $f_2 = \frac{uv}{(u + v)}$.

$f_2$ = [1]

(f)

Suggest which value of focal length, $f_1$ or $f_2$, might be more accurate. Explain your answer.

[1]

Show the mark scheme

These are the official mark-scheme rows. Each point that matches your answer earns a mark.

Tap the mark scheme to open it full size.

Show a worked answer

How to reach each mark, step by step. Try the question yourself first.

3(a)(i)

  • Move the screen slowly back and forth around the sharpest position, then leave it where the image is clearest.

3(a)(ii)

  • Measure $v$ from the lens to the sharp image on the screen. Measure $h_O$ and $h_I$ as the object and image heights.
  • For example, readings could be $v = \mathbf{60.0}\,\mathrm{cm}$, $h_O = \mathbf{2.0}\,\mathrm{cm}$ and $h_I = \mathbf{6.0}\,\mathrm{cm}$. Record your own measurements.

3(a)(iii)

  • Use $M = h_I/h_O$. For example, if $h_I = 6.0\,\mathrm{cm}$ and $h_O = 2.0\,\mathrm{cm}$, then $M = 6.0\,\mathrm{cm}/2.0\,\mathrm{cm} = \mathbf{3.0}$. Use your own heights; magnification has no unit.

3(b)

  • Use $f_1 = v/(M+1)$. For example, if $v = 60.0\,\mathrm{cm}$ and $M = 3.0$, then $f_1 = 60.0\,\mathrm{cm}/(3.0+1) = \mathbf{15.0}\,\mathrm{cm}$. Use your own values.

3(c)

  • The ruler or your hand can block the light when measuring the image.
  • Use a translucent screen and measure the image from the back, where the ruler will not block the light.

3(d)

  • Move the screen until the image is sharp, then measure from the lens to the screen. For example, $v = \mathbf{24.0}\,\mathrm{cm}$. Use your own measurement.

3(e)

  • Use $f_2 = uv/(u+v)$. For example, with $u = 40.0\,\mathrm{cm}$ and $v = 24.0\,\mathrm{cm}$, $f_2 = (40.0\,\mathrm{cm})(24.0\,\mathrm{cm})/(40.0\,\mathrm{cm}+24.0\,\mathrm{cm}) = \mathbf{15.0}\,\mathrm{cm}$. Use your measured $v$.

3(f)

  • Choose $\mathbf{f_2}$. The small height measurements used for $f_1$ have larger percentage uncertainties: the same ruler error is a larger fraction of a smaller measurement.
Original question

Log in or create account

IGCSE, A-Level & AP