Skip to content

IGCSE Physics · March 2023 · Paper 62 · Difficulty 3 · Standard

Question 1

1

A student determines the diameter of a marble by two methods and calculates the density of the material from which the marble is made.

Some marbles are shown full size in Fig. 1.1.

Method 1

(a)
(i)

On Fig. 1.1, measure the length D.

D = cm

Using your value of D, calculate the average diameter d$_1$ of one marble.

d$_1$ = cm[2]

(ii)

Suggest why it is more accurate, when using a ruler, to measure D for five marbles rather than measure the diameter of a single marble.

[1]

Method 2

(b)

Fig. 1.2 shows two wooden blocks and one of the marbles.

Describe how the student uses the two blocks and the marble to determine a new accurate value for the diameter of a marble.

Draw a diagram to show the arrangement.

Describe clearly how the student ensures that the value for the diameter of a marble is as accurate as possible.

[2]

(c)
(i)

The student uses the top pan balance as shown in Fig. 1.3 to measure the mass of the five marbles.

He measures the mass M$_0$ of a beaker without the marbles and then measures the mass M$_5$ of the same beaker containing the marbles.

Fig. 1.3

Record the values of M$_0$ and M$_5$ as shown on the top pan balance in Fig. 1.3.

M$_0$ = g

M$_5$ = g

Use these values to calculate the average mass m of one marble.

m = g[1]

(ii)

The student pours water into a measuring cylinder.

He records the reading V$_1$ of the water level in the measuring cylinder.

V$_1$ = 26 cm$^3$

The student places the five marbles into the water in the measuring cylinder as shown in Fig. 1.4.

Record the new reading V$_2$ of the water level in the measuring cylinder shown in Fig. 1.4.

V$_2$ = cm$^3$[1]

(iii)

Calculate a value for the average volume V of one marble. Use the values from (c)(ii) and the equation

$V = \frac{V_2 - V_1}{5}$

V = cm$^3$[1]

(iv)

Calculate a value for the density $\rho$ of the material from which the marble is made. Use your values of m from (c)(i), V from (c)(iii) and the equation

$\rho = \frac{m}{V}$

$\rho$ = g/cm$^3$[1]

(d)

Describe one possible source of inaccuracy in the method described in (c) and suggest one improvement to reduce its effect.

source of inaccuracy

improvement

[2]

Show the mark scheme

These are the official mark-scheme rows. Each point that matches your answer earns a mark.

Tap the mark scheme to open it full size.

Show a worked answer

How to reach each mark, step by step. Try the question yourself first.

1(a)(i)

  • The measured length is $D = \mathbf{7.8}\,\mathrm{cm}$. Use $d_1 = D/5$ to find the mean diameter.
  • $d_1 = (7.8\,\mathrm{cm})/5 = \mathbf{1.6}\,\mathrm{cm}$.

1(a)(ii)

  • The ruler uncertainty is a smaller fraction of the longer length $D$, so the average diameter is more precise.

1(b)

  • Place the marble between the two blocks and measure the gap between them.
  • Measure the gap in two places to check the blocks are parallel, then use the gap as the diameter.

1(c)(i)

  • The balance readings are $M_0 = \mathbf{30.8}\,\mathrm{g}$ and $M_5 = \mathbf{64.3}\,\mathrm{g}$.
  • Use $m = (M_5-M_0)/5$ to find the average mass.
  • $m = (64.3\,\mathrm{g} - 30.8\,\mathrm{g})/5 = \mathbf{6.7}\,\mathrm{g}$.

1(c)(ii)

  • Read the bottom of the meniscus: $V_2 = \mathbf{38}\,\mathrm{cm^3}$.

1(c)(iii)

  • Use $V = (V_2-V_1)/5$ to find the volume per marble.
  • $V = (38\,\mathrm{cm^3} - 26\,\mathrm{cm^3})/5 = \mathbf{2.4}\,\mathrm{cm^3}$.

1(c)(iv)

  • Use $\rho = m/V$.
  • $\rho = (6.7\,\mathrm{g})/(2.4\,\mathrm{cm^3}) = \mathbf{2.8}\,\mathrm{g/cm^3}$.

1(d)

  • The cylinder divisions may be large compared with the volume change.
  • Use more marbles to make the volume change larger and reduce the percentage uncertainty.
Original question

Log in or create account

IGCSE, A-Level & AP