Skip to content

IGCSE Physics · March 2023 · Paper 52 · Difficulty 2 · Core

Question 3

3

In this experiment, you will determine the resistance per unit length of a resistance wire. The circuit has been set up for you.

Carry out the following instructions, referring to Fig. 3.1.

(a)

Connect the crocodile clip to a length $l = 20.0\text{ cm}$ of the resistance wire.

Close the switch.

Measure and record in Table 3.1, the value of potential difference (p.d.) $V$ and current $I$ for the resistance wire.

Connect the crocodile clip to lengths $l = 40.0\text{ cm}$, $l = 60.0\text{ cm}$, $l = 80.0\text{ cm}$ and $l = 100.0\text{ cm}$ of the resistance wire.

For each length $l$, measure and record in Table 3.1, the value of potential difference $V$ and current $I$ for the resistance wire.

Open the switch.

Table 3.1

$l/\text{cm}$$V/\text{V}$$I/\text{A}$$R/\Omega$
20.0
40.0
60.0
80.0
100.0

[2]

(b)

For each length $l$ calculate and record in Table 3.1, the resistance $R$ of the resistance wire. Use your values of $V$ and $I$ from Table 3.1 and the equation

$$R = \frac{V}{I}.$$

[2]

(c)

Plot a graph of $R/\Omega$ ($y$-axis) against $l/\text{cm}$ ($x$-axis). Draw a straight line of best fit.

[4]

(d)
(i)

Determine the gradient $G$ of the graph. Show clearly on the graph how you obtained the necessary information.

$G =$ [1]

(ii)

The gradient $G$ is numerically equal to the resistance per unit length $R_0$ of the resistance wire. Write down the value of $R_0$ for the resistance wire.

$R_0 =$ $\Omega/\text{cm}$[1]

(e)

Suggest one practical reason why students carrying out this experiment may not obtain the same readings as yours. Assume that the procedure has been done carefully.

[1]

[Total: 11]

Show the mark scheme

These are the official mark-scheme rows. Each point that matches your answer earns a mark.

Tap the mark scheme to open it full size.

Show a worked answer

How to reach each mark, step by step. Try the question yourself first.

3(a)

  • For each wire length, record the voltmeter and ammeter readings in the table. Open the switch after taking the readings.
  • The p.d. should increase and the current should decrease as the length increases. The readings should be below $4\,\mathrm{V}$ and $1\,\mathrm{A}$.

3(b)

  • Use $R = V/I$ for each row. For example, if $V = 1.20\,\mathrm{V}$ and $I = 0.30\,\mathrm{A}$, then $R = (1.20\,\mathrm{V})/(0.30\,\mathrm{A}) = \mathbf{4.0}\,\Omega$.
  • Record all five results to the same number of significant figures: either two or three.

3(c)

  • Label the horizontal axis $l/\mathrm{cm}$ and the vertical axis $R/\Omega$. Choose scales so the points occupy at least half the grid.
  • Plot all five pairs from your table within half a small square. Draw a thin, straight line of best fit through the trend.

3(d)(i)

  • Use $G = \Delta R/\Delta l$. Draw a large triangle on the best-fit line and show the readings used for its rise and run.
  • For example, if the rise is $6.0\,\Omega$ over $75\,\mathrm{cm}$, then $G = (6.0\,\Omega)/(75\,\mathrm{cm}) = \mathbf{0.080}\,\mathrm{\Omega/cm}$. Use your own graph.

3(d)(ii)

  • Use $R_0 = G$: the gradient gives resistance per unit length. For example, if $G = 0.080\,\mathrm{\Omega/cm}$, then $R_0 = \mathbf{0.080}\,\mathrm{\Omega/cm}$. Use your own gradient.

3(e)

  • Different samples of resistance wire may have different thicknesses, so even equal lengths can have different resistances and give different readings.
Original question

Log in or create account

IGCSE, A-Level & AP