Skip to content

IGCSE Physics · March 2023 · Paper 52 · Difficulty 3 · Standard

Question 1

1

In this experiment, you will determine the diameter of a marble by two methods and calculate the density of the material from which the marble is made.

Method 1

Carry out the following instructions, referring to Fig. 1.1.

Fig. 1.1 (Apparatus viewed from above)
(a)
(i)

Place the metre ruler on the bench with its scale facing upwards. Arrange one of the wooden blocks and the five marbles as shown in Fig. 1.1.

Measure the length $D$ for the five marbles.

$D =$ $\text{cm}$

Using your value of $D$, calculate the average diameter $d_1$ of one marble.

$d_1 =$ $\text{cm}$[2]

(ii)

Suggest why it is more accurate, when using a ruler, to measure $D$ for five marbles rather than measure the diameter of a single marble.

[1]

Method 2

(b)

Describe how the two wooden blocks and one of the marbles can be used to determine an accurate value for the diameter of a marble.

Draw a diagram to show your suggested arrangement.

Describe clearly how you ensure that your value for the diameter of a marble is as accurate as possible.

Use your arrangement to measure the diameter $d_2$ of the marble.

$d_2 =$ $\text{cm}$[2]

(c)
(i)

Use the top-pan balance as shown in Fig. 1.2 to measure the mass $m$ of one of the marbles.

$m =$ $\text{g}$[1]

(ii)

Pour approximately $25\text{ cm}^3$ of water into the measuring cylinder.

Record the reading $V_1$ of the water level in the measuring cylinder.

$V_1 =$ $\text{cm}^3$

Carefully place the 5 marbles into the water in the measuring cylinder as shown in Fig. 1.3.

Record the new reading $V_2$ of the water level in the measuring cylinder.

$V_2 =$ $\text{cm}^3$

Calculate a value for the average volume $V$ of one marble. Use the equation

$$V = \frac{V_2 - V_1}{5}$$

$V =$ $\text{cm}^3$[1]

(iii)

Draw, on Fig. 1.3, an arrow showing the correct line of sight for reading the water level in the measuring cylinder.[1]

(iv)

Calculate a value for the density $\rho$ of the material from which the marble is made. Use your values of $m$ from (c)(i), $V$ from (c)(ii) and the equation

$$\rho = \frac{m}{V}$$

$\rho =$ $\text{g/ cm}^3$[1]

(d)

Describe one possible source of inaccuracy in the method described in (c) and suggest one improvement to reduce its effect.

source of inaccuracy

improvement [2]

[Total: 11]

Show the mark scheme

These are the official mark-scheme rows. Each point that matches your answer earns a mark.

Tap the mark scheme to open it full size.

Show a worked answer

How to reach each mark, step by step. Try the question yourself first.

1(a)(i)

  • Measure $D$ across all five touching marbles. Record your reading in $\mathrm{cm}$.
  • Use $d_1 = D/5$. For example, if $D = 8.00\,\mathrm{cm}$, then $d_1 = (8.00\,\mathrm{cm})/5 = \mathbf{1.60}\,\mathrm{cm}$.

1(a)(ii)

  • The same ruler uncertainty is a smaller fraction of the longer length $D$, so the average diameter is more precise.

1(b)

  • Draw the marble touching the flat faces of two blocks. Measure the gap between the blocks with a ruler; this is $d_2$.
  • Measure the gap at two places and check that it is the same, so the blocks are parallel. Record your measured $d_2$ in $\mathrm{cm}$.

1(c)(i)

  • Zero the balance, then place one marble on the pan. Record its mass to at least one decimal place, for example $m = \mathbf{5.0}\,\mathrm{g}$; use your own reading.

1(c)(ii)

  • Read $V_1$ before adding the marbles and $V_2$ afterwards. The marbles displace water, so $V_2$ is greater than $V_1$.
  • Use $V = (V_2 - V_1)/5$. For example, if $V_1 = 25.0\,\mathrm{cm^3}$ and $V_2 = 35.0\,\mathrm{cm^3}$, then $V = (35.0-25.0)\,\mathrm{cm^3}/5 = \mathbf{2.0}\,\mathrm{cm^3}$.

1(c)(iii)

  • Draw a horizontal arrow at the level of the bottom of the meniscus. This avoids parallax error.

1(c)(iv)

  • Use $\rho = m/V$, with your mass and volume for one marble.
  • For example, if $m = 5.0\,\mathrm{g}$ and $V = 2.0\,\mathrm{cm^3}$, then $\rho = (5.0\,\mathrm{g})/(2.0\,\mathrm{cm^3}) = \mathbf{2.5}\,\mathrm{g/cm^3}$.

1(d)

  • The measuring cylinder divisions may be large compared with the volume change.
  • Use more marbles to make the volume change larger and reduce the percentage uncertainty.
Original question

Log in or create account

IGCSE, A-Level & AP