Skip to content

IGCSE Physics · March 2022 · Paper 62 · Difficulty 3 · Standard

Question 3

3

A student investigates the refraction of light by a transparent block.

The student’s ray-trace sheet is shown full size in Fig. 3.1.

Fig. 3.1
(a)

The student places a transparent block ABCD near the centre of the ray-trace sheet, as indicated in Fig. 3.1.

(i)

Draw a normal to point N extending above AB. Label the upper end of the normal with the letter L.[1]

(ii)

The student draws the line EN, as shown in Fig. 3.1.

On Fig. 3.1, measure the angle $\theta_1$ between the lines LN and EN.

$\theta_1$ = [1]

(b)

The student places two pins, $P_1$ and $P_2$, on the line EN, as shown in Fig. 3.1.

(i)

Measure the distance $d$ between pins $P_1$ and $P_2$.

$d$ = [1]

(ii)

Suggest whether the two pins are a suitable distance apart for accurate ray tracing. Explain your answer.

statement

explanation [1]

(c)

The student places a plane mirror on line CD and views the images of pins $P_1$ and $P_2$ through the transparent block.

She places two pins, $P_3$ and $P_4$, so that these pins, and the images of pins $P_1$ and $P_2$, all appear exactly one behind the other.

On Fig. 3.1:

  • Draw a line through points $P_3$ and $P_4$ and extend the line 3 cm below CD.
  • Label the point at which this line meets AB with the letter G.
  • Label the lower end of the line with the letter H. [1]

(d)

The student repeats the procedure for an angle $\theta_2 = 35^{\circ}$.

She places two pins, $P_5$ and $P_6$, so that these pins, and the images of pins $P_1$ and $P_2$, all appear exactly one behind the other.

On Fig. 3.1:

  • Draw a line through points $P_5$ and $P_6$ and extend the line 3 cm below CD.
  • Label the point at which this line meets AB with the letter R.
  • Label the lower end of this line with the letter S.
  • Label the point at which GH and RS cross with the letter T.
(i)

Measure the angle $\beta$, where $\beta$ is the angle between lines GT and RT.

$\beta$ = [1]

(ii)

A student suggests that the angle $\beta$ should be equal to $\theta_s$, where $\theta_s$ is calculated using the equation

$\theta_s = \theta_2 - \theta_1$

State whether your results from (a)(ii) and (d) support this suggestion. Justify your answer by reference to values from your results.

statement

justification [2]

(e)

Suggest two precautions to take in this type of experiment to ensure accurate results.

  1. [2]
(f)

Suggest one reason why different students, all carrying out this experiment carefully, may not obtain identical results.

[1]

[Total: 11]

Show the mark scheme

These are the official mark-scheme rows. Each point that matches your answer earns a mark.

Tap the mark scheme to open it full size.

Show a worked answer

How to reach each mark, step by step. Try the question yourself first.

3(a)(i)

  • Draw $NL$ perpendicular to $AB$ at $N$. Extend it above $AB$ and label its upper end $L$.

3(a)(ii)

  • Measure between $LN$ and $EN$ with a protractor: $\theta_1 = \mathbf{15}^\circ$.

3(b)(i)

  • Measure between the pin centres: $d = \mathbf{3.0}\,\mathrm{cm}$.

3(b)(ii)

  • The separation is not suitable. Place the pins much further apart to make the direction easier to judge accurately.

3(c)

  • Draw a straight line through $P_3$ and $P_4$, continuing it $3\,\mathrm{cm}$ below $CD$. Label its intersection with $AB$ as $G$ and its lower end $H$.

3(d)(i)

  • Measure the angle between $GT$ and $RT$: $\beta = \mathbf{18}^\circ$.

3(d)(ii)

  • Use $\theta_s=\theta_2-\theta_1$.
  • $\theta_s=35^{\circ}-15^{\circ}=\mathbf{20}^{\circ}$. This is close to $\beta=18^{\circ}$, so the results support the suggestion within measurement uncertainty.

3(e)

  • Use a sharp pencil to draw thin lines, so their positions are easier to judge.
  • Keep the pins upright when aligning them.

3(f)

  • It is difficult to align the pins exactly, so students can draw slightly different rays.
Original question

Log in or create account

IGCSE, A-Level & AP