Skip to content

IGCSE Physics · March 2020 · Paper 52 · Difficulty 3 · Standard

Question 3

3

In this experiment, you will investigate a power supply. The circuit has been set up for you.

Carry out the following instructions, referring to Fig. 3.1.

(a)

Connect the crocodile clip to a length $l = 100.0\text{ cm}$ of the resistance wire.

Switch on.

Measure the value of potential difference $V_0$ and current $I_0$ for the wire.

$V_0 =$ $\text{V}$

$I_0 =$ $\text{A}$

Switch off.

Calculate the resistance $R_0$ of $100.0\text{ cm}$ of the wire. Use your values of $V_0$ and $I_0$ and the equation $R_0 = \frac{V_0}{I_0}$.

$R_0 =$ $\Omega$[1]

(b)
(i)

Switch on.

Connect the crocodile clip to lengths $l = 70.0\text{ cm}$, $60.0\text{ cm}$, $50.0\text{ cm}$, $40.0\text{ cm}$ and $30.0\text{ cm}$ of the resistance wire in turn.

For each length $l$ measure the current $I$ in the circuit. Record your readings in Table 3.1.[1]

Switch off.

Table 3.1

$l / \text{cm}$$I / \text{A}$$\frac{1}{I} / \frac{1}{\text{A}}$
70.0
60.0
50.0
40.0
30.0
(ii)

Calculate, and record in Table 3.1, the value of $\frac{1}{I}$ for each length $l$ of the wire.[1]

(c)

Plot a graph of $l / \text{cm}$ ($y$-axis) against $\frac{1}{I} / \frac{1}{\text{A}}$ ($x$-axis). You do not need to start your axes at the origin $(0,0)$.

[4]

(d)
(i)

Determine the gradient $G$ of the graph. Show clearly on the graph how you obtained the necessary information.

$G =$ [1]

(ii)

Calculate the electromotive force (e.m.f.) $E$ of the power supply. Use your value of $R_0$ from (a) and the equation $E = \frac{G \times R_0}{k}$, where $k = 100\text{ cm}$.

$E =$ $\text{V}$[1]

(e)

The ammeter in this circuit has a small resistance which affects the current. The effect of this resistance on the measured current $I$ will be different for each measured length $l$ of the resistance wire.

State and explain which length $l$ will be most affected by the resistance of the ammeter.

statement

explanation

[2]

[Total: 11]

Show the mark scheme

These are the official mark-scheme rows. Each point that matches your answer earns a mark.

Tap the mark scheme to open it full size.

Show a worked answer

How to reach each mark, step by step. Try the question yourself first.

3(a)

  • Read $V_0$ and $I_0$ from your meters. Use $R_0 = \dfrac{V_0}{I_0}$ to find the resistance.
  • For example, if $V_0 = 2.0\,\mathrm{V}$ and $I_0 = 0.20\,\mathrm{A}$, $R_0 = \dfrac{2.0\,\mathrm{V}}{0.20\,\mathrm{A}} = \mathbf{10}\,\mathrm{\Omega}$. Your readings may differ.

3(b)(i)

  • Record the current at each length to at least two decimal places. Use your own meter readings.
  • The current should increase as the wire gets shorter, because the resistance of the wire falls.

3(b)(ii)

  • Use $1/I$ for each row: divide 1 by that row’s measured current.
  • For example, if $I = 0.40\,\mathrm{A}$, $1/I = 1/(0.40\,\mathrm{A}) = \mathbf{2.5}\,\mathrm{1/A}$. Repeat for your other readings.

3(c)

  • Label the vertical axis $l/\mathrm{cm}$ and the horizontal axis $(1/I)/(\mathrm{1/A})$.
  • Choose scales so the points occupy at least half the grid, then plot each point within half a small square.
  • Draw a thin, well-judged best-fit line through the trend of the points.

3(d)(i)

  • Draw a large triangle on your best-fit line and use $G = \dfrac{\Delta l}{\Delta(1/I)}$.
  • For example, if $\Delta l = 50\,\mathrm{cm}$ and $\Delta(1/I) = 2.5\,\mathrm{1/A}$, $G = \dfrac{50\,\mathrm{cm}}{2.5\,\mathrm{1/A}} = \mathbf{20}\,\mathrm{A\,cm}$. Use points on your own line.

3(d)(ii)

  • Use $E = \dfrac{GR_0}{k}$, where $k = 100\,\mathrm{cm}$.
  • For example, with $G = 20\,\mathrm{A\,cm}$ and $R_0 = 10\,\mathrm{\Omega}$, $E = \dfrac{(20\,\mathrm{A\,cm})(10\,\mathrm{\Omega})}{100\,\mathrm{cm}} = \mathbf{2.0}\,\mathrm{V}$. Use your own results.

3(e)

  • The $\mathbf{30.0}\,\mathrm{cm}$ length is most affected.
  • It has the smallest wire resistance, so the ammeter makes up a greater fraction of the total resistance.
Original question

Log in or create account

IGCSE, A-Level & AP