Skip to content

IGCSE Physics · March 2020 · Paper 52 · Difficulty 3 · Standard

Question 1

1

In this experiment, you will determine the density of wood by two methods.

Carry out the following instructions, referring to Fig. 1.1.

Method 1

(a)
(i)

Use a ruler to measure the length $l$ and the diameter $d$ of the wooden rod you are using.

$l$ = cm

$d$ = cm[2]

(ii)

Suggest a more accurate method for measuring the diameter of the rod.

List any additional apparatus you would require and briefly describe how you would determine the diameter. You may draw a diagram if it helps to explain your answer.

You are not asked to carry out this method.

[2]

(b)

Measure the mass $m$ of the wooden rod using the balance provided.

$m$ = g[1]

(c)

Calculate a value $\rho_1$ for the density of the wooden rod. Use your values from (a)(i) and (b) and the equation $\rho_1 = \dfrac{4m}{\pi d^{2}l}$. Include a suitable unit.

$\rho_1$ = [2]

Method 2

(d)
(i)

Pour approximately $150\ \mathrm{cm}^{3}$ of water into the measuring cylinder.

Record the reading $V_1$ of the water level in the measuring cylinder.

$V_1$ = cm$^{3}$

Gently lower the wooden rod into the water so that it floats freely as shown in Fig. 1.2.

Record the new reading $V_2$ of the water level in the measuring cylinder.

$V_2$ = cm$^{3}$[1]

(ii)

On Fig. 1.2, draw an arrow on the left‑hand side showing the correct line of sight for reading the volume of water in the measuring cylinder.[1]

(e)

Remove the rod from the measuring cylinder and lower the modelling clay into the water until it is completely submerged as shown in Fig. 1.3.

Record the new reading $V_3$ of the water level in the measuring cylinder.

$V_3$ = cm$^{3}$

Remove the modelling clay from the measuring cylinder.

Attach the rod to the modelling clay using the hook on the modelling clay and the loop of thread on the rod as shown in Fig. 1.4.

Lower the modelling clay and rod into the water until the rod is completely submerged.

Record the new reading $V_4$ of the water level in the measuring cylinder.

$V_4$ = cm$^{3}$

Calculate another value $\rho_2$ for the density of the wooden rod.

Use your values from (d) and (e) and the equation $\rho_2 = \dfrac{(V_2 - V_1)}{(V_4 - V_3)} \times k$ where $k = 1.0\ \mathrm{g\,/\,cm^{3}}$.

$\rho_2$ = [2]

[Total: 11]

Show the mark scheme

These are the official mark-scheme rows. Each point that matches your answer earns a mark.

Tap the mark scheme to open it full size.

Show a worked answer

How to reach each mark, step by step. Try the question yourself first.

1(a)(i)

  • Measure your own rod. For example, its length could be $l = \mathbf{3.0}\,\mathrm{cm}$ and its diameter $d = \mathbf{2.4}\,\mathrm{cm}$.
  • Record both measurements to one decimal place in cm.

1(a)(ii)

  • Use vernier callipers to measure the diameter at several places along the rod.
  • Find the mean of the readings to reduce the effect of variations in diameter.

1(b)

  • Place the rod on the balance and record its mass. For example, $m = \mathbf{9.5}\,\mathrm{g}$; your reading may differ.

1(c)

  • Use $\rho_1 = \dfrac{4m}{\pi d^2l}$, because the rod is a cylinder.
  • For example, with $m = 9.5\,\mathrm{g}$, $d = 2.4\,\mathrm{cm}$ and $l = 3.0\,\mathrm{cm}$, $\rho_1 = \dfrac{4(9.5\,\mathrm{g})}{\pi(2.4\,\mathrm{cm})^2(3.0\,\mathrm{cm})} = \mathbf{0.70}\,\mathrm{g/cm^3}$.

1(d)(i)

  • Read the water level before and after adding your rod. For example, $V_1 = \mathbf{150.0}\,\mathrm{cm^3}$ and $V_2 = \mathbf{159.5}\,\mathrm{cm^3}$.
  • The floating rod displaces water, so $V_2$ is greater than $V_1$. Your readings will depend on your apparatus.

1(d)(ii)

  • Draw a horizontal arrow at the level of the bottom of the meniscus, pointing towards the cylinder. This avoids a parallax error.

1(e)

  • Measure $V_3$ with the clay submerged and $V_4$ with both clay and rod submerged. For example, $V_3 = 160.0\,\mathrm{cm^3}$ and $V_4 = 173.6\,\mathrm{cm^3}$.
  • Use $\rho_2 = \dfrac{V_2-V_1}{V_4-V_3}k$. The two differences give the displaced volumes for the floating and submerged rod.
  • For example, with $V_1 = 150.0\,\mathrm{cm^3}$ and $V_2 = 159.5\,\mathrm{cm^3}$, $\rho_2 = \dfrac{(159.5-150.0)\,\mathrm{cm^3}}{(173.6-160.0)\,\mathrm{cm^3}}(1.0\,\mathrm{g/cm^3}) = \mathbf{0.70}\,\mathrm{g/cm^3}$.
  • Compare this with your value of $\rho_1$: the two should be within $10\%$ of each other.
Original question

Log in or create account

IGCSE, A-Level & AP