Skip to content

IGCSE Physics · November 2024 · Paper 51 · Difficulty 3 · Standard

Question 1

1

In this experiment, you will investigate the period of a pendulum.

Refer to Fig. 1.1 and Fig. 1.2.

A pendulum has been set up for you as shown in Fig. 1.1. Do not change the height of the support.

(a)

• Adjust the length of the pendulum until the distance d measured from the bottom of the support to the centre of the bob is 90.0 cm.

  • Displace the bob slightly and release it so that it swings. Fig. 1.2 shows one complete oscillation of the pendulum.
  • Measure, and record in Table 1.1, the time t for 10 complete oscillations.
  • Calculate, and record in Table 1.1, the period T of the pendulum. The period is the time for one complete oscillation.
  • Calculate $T^{2}$ and record in Table 1.1. [2]
d/cmt/sT/s$T^{2}$/ $s^{2}$
90.0
45.0
(b)

Repeat the procedure in (a) using a distance d = 45.0 cm.[3]

(c)

Explain why timing 10 oscillations gives a more accurate result for the period T than timing 1 oscillation.[1]

(d)

Describe one technique that you use to improve accuracy when measuring the distance d.

You may draw a diagram to help your description.[1]

(e)

Describe one technique that you use to improve accuracy when measuring the time t for 10 oscillations.[1]

(f)

Measure the distance x between the bottom of the support and the floor. Give your answer to the nearest cm.

x = cm[1]

(g)

A student plans to plot a graph of $T^{2}$ against d. Suggest suitable values of d that the student can use to obtain measurements that are sufficient for this task.[2]

Show the mark scheme

These are the official mark-scheme rows. Each point that matches your answer earns a mark.

Tap the mark scheme to open it full size.

Show a worked answer

How to reach each mark, step by step. Try the question yourself first.

1(a)

  • Time 10 complete swings and record your measured $t$. For example, $t = 19.0\,\mathrm{s}$.
  • Use $T = t/10$. For this example, $T = 19.0\,\mathrm{s}/10 = \mathbf{1.90}\,\mathrm{s}$.
  • Use $T^2 = T\times T$. Here, $T^2 = (1.90\,\mathrm{s})^2 = \mathbf{3.61}\,\mathrm{s^2}$.

1(b)

  • Repeat the timing at $d = 45.0\,\mathrm{cm}$. For example, your measured time might be $t = 13.5\,\mathrm{s}$.
  • Use $T = t/10$. Here, $T = 13.5\,\mathrm{s}/10 = \mathbf{1.35}\,\mathrm{s}$.
  • Use $T^2 = T\times T$. Here, $T^2 = (1.35\,\mathrm{s})^2 = \mathbf{1.82}\,\mathrm{s^2}$, to three significant figures, as in part (a).

1(c)

  • Timing 10 oscillations makes reaction-time errors a smaller fraction of the total time, so the period is more accurate.

1(d)

  • Use a set square to line up the centre of the bob with the scale on a ruler held close to it.

1(e)

  • Use a fixed marker. Start timing as the bob passes it, then count 10 complete oscillations, stopping as the bob passes it in the same direction.

1(f)

  • Measure vertically from the bottom of the support to the floor. Record your own measurement to the nearest centimetre; for example, $x = \mathbf{150}\,\mathrm{cm}$.

1(g)

  • As well as $45.0\,\mathrm{cm}$ and $90.0\,\mathrm{cm}$, use $\mathbf{25.0}\,\mathrm{cm}$, $\mathbf{60.0}\,\mathrm{cm}$ and $\mathbf{75.0}\,\mathrm{cm}$, provided each is less than the measured height $x$.
Original question

Log in or create account

IGCSE, A-Level & AP