Skip to content

IGCSE Physics · November 2022 · Paper 63 · Difficulty 3 · Standard

Question 1

1

A student investigates the dimensions of a boiling tube.

She uses the apparatus shown in Fig. 1.1.

(a)

The student pours a small amount of water into the boiling tube and measures the height $h_0$ from the bench to the initial water level.

$h_0$ = 2.6 cm

Suggest one precaution that is taken when measuring the height of the water level to ensure the reading is accurate.

You may draw a diagram if it helps your explanation.[1]

(b)

The student uses a measuring cylinder graduated in $cm^3$ to add a volume of water $V = 5.0\ \mathrm{cm^3}$ to the boiling tube.

Part of the boiling tube, after the water has been added, is shown full size in Fig. 1.2.

Fig. 1.2

Measure, and record in the first row of Table 1.1, the new height $h$ of the water level from the bench.[1]

Table 1.1

V/cm³h/cmH/cm
5.0
10.05.52.9
15.06.74.1
20.08.35.7
25.09.67.0
(c)

For the value of $V = 5.0\ \mathrm{cm^3}$, calculate, and record in Table 1.1, the increase in height $H$ of the water in the boiling tube. Use the value of $h_0$ from (a), your value of $h$ in Table 1.1 and the equation $H = (h - h_0)$.[1]

(d)

Plot a graph of $V/\mathrm{cm^3}$ (y-axis) against $H/\mathrm{cm}$ (x-axis).

[4]

(e)
(i)

Determine the gradient of the graph. Show clearly on the graph how you obtained the necessary information.

gradient = [1]

(ii)

Calculate $D$, the inside diameter of the boiling tube.

Use the equation $D = \sqrt{\frac{4G}{\pi}}$, where $G$ is numerically equivalent to the gradient in (e)(i).

$D$ = cm[1]

(f)

Suggest why it was important for the student to add a small volume of water at the start of the experiment.[1]

(g)

Another student uses this experiment, with the same apparatus, to measure $D$ for a small test-tube of diameter approximately 1.2 cm. He adds water in volumes of 1.0 $cm^3$ at a time.

State and explain one reason why this is not an accurate method to use for this test-tube.[1]

Show the mark scheme

These are the official mark-scheme rows. Each point that matches your answer earns a mark.

Tap the mark scheme to open it full size.

Show a worked answer

How to reach each mark, step by step. Try the question yourself first.

1(a)

  • Use a horizontal set square to transfer the water level to a ruler held close to the tube.

1(b)

  • The height from the bench to the water level is $h = \mathbf{4.0}\,\mathrm{cm}$.

1(c)

  • Use $H = h-h_0 = 4.0\,\mathrm{cm}-2.6\,\mathrm{cm} = \mathbf{1.4}\,\mathrm{cm}$.

1(d)

  • Label the horizontal axis $H/\mathrm{cm}$ and the vertical axis $V/\mathrm{cm^3}$. Choose even scales that use at least half the grid.
  • Plot $(1.4,5.0)$, $(2.9,10.0)$, $(4.1,15.0)$, $(5.7,20.0)$ and $(7.0,25.0)$. Draw a thin best-fit line.

1(e)(i)

  • Use $G = \Delta V/\Delta H$. Draw a large triangle on the best-fit line and use its corners to find the gradient.
  • For example, $G = (25.0-5.0)\,\mathrm{cm^3}/(7.0-1.4)\,\mathrm{cm} = \mathbf{3.57}\,\mathrm{cm^2}$. Your result depends on your line.

1(e)(ii)

  • Use $D = \sqrt{4G/\pi}$, with $G$ numerically equal to your gradient.
  • For $G = 3.57\,\mathrm{cm^2}$, $D = \sqrt{4(3.57\,\mathrm{cm^2})/\pi} = \mathbf{2.13}\,\mathrm{cm}$.

1(f)

  • The tube is curved near its base, so its inside diameter is not uniform there. The initial water fills this part.

1(g)

  • Each $1.0\,\mathrm{cm^3}$ volume is small, so uncertainty in the measuring cylinder reading is a large fraction of it.
Original question

Log in or create account

IGCSE, A-Level & AP