Skip to content

IGCSE Physics · June 2025 · Paper 53 · Difficulty 3 · Standard

Question 1

1

In this experiment, you will investigate a suspended metre ruler and determine the weight of the metre ruler.

Refer to Fig. 1.1. Do not change the position of the loops of thread attached to the force meters.

Fig. 1.1
(a)
(i)

Move the $1.50\text{ N}$ load to a distance $d = 40.0\text{ cm}$ from the $0.0\text{ cm}$ end of the ruler.

Raise or lower one clamp slightly, if necessary, so that the metre ruler is as near to horizontal as possible.

Read the value $F_X$ on force meter X and the value $F_Y$ on force meter Y.

$F_X =$ $\text{N}$

$F_Y =$ $\text{N}$

Calculate a value $W_X$ using the equation $W_X = F_X + F_Y - k$, where $k = 1.50\text{ N}$.

$W_X =$ $\text{N}$[1]

(ii)

Briefly describe how to check that the ruler is horizontal before taking the reading. You may draw a diagram.

[1]

(b)

Move the $1.50\text{ N}$ load to a distance $d = 10.0\text{ cm}$ from the $0.0\text{ cm}$ end of the ruler. Ensure that the metre ruler is as near to horizontal as possible.

Read, and record in Table 1.1, the value $F_X$ on force meter X.

Repeat this procedure for $d = 30.0\text{ cm}$, $50.0\text{ cm}$, $70.0\text{ cm}$ and $90.0\text{ cm}$.

Table 1.1

$d/\text{cm}$$F_X/\text{N}$
10.0
30.0
50.0
70.0
90.0

[2]

(c)

Plot a graph of $F_X/\text{N}$ (y-axis) against $d/\text{cm}$ (x-axis). Start the axes at the origin $(0,0)$.

Draw a best-fit straight line.

[4]

(d)

From your graph, determine $F_0$, the value of $F_X$ when $d = 0.0\text{ cm}$.

$F_0 =$

Calculate the weight $W_R$ of the metre ruler, using the equation $W_R = 2 \times F_0$.

$W_R =$ $\text{N}$[2]

(e)

State and explain whether your plots made it easy to choose the best-fit line. Justify your answer with reference to your plots.

statement

explanation

[1]

[Total: 11]

Show the mark scheme

These are the official mark-scheme rows. Each point that matches your answer earns a mark.

Tap the mark scheme to open it full size.

Show a worked answer

How to reach each mark, step by step. Try the question yourself first.

1(a)(i)

  • Read both force meters. The values depend on your apparatus.
  • Use $W_X = F_X + F_Y - k$. For example, if $F_X = 0.80\,\mathrm{N}$ and $F_Y = 1.20\,\mathrm{N}$, then $W_X = 0.80\,\mathrm{N} + 1.20\,\mathrm{N} - 1.50\,\mathrm{N} = \mathbf{0.50}\,\mathrm{N}$.

1(a)(ii)

  • Measure the height of the ruler above the bench at two places. Adjust the ruler until the two heights are equal.

1(b)

  • Record the five readings from your force meter. They should increase as the load moves towards meter X.
  • Use the same number of decimal places for all five readings, matching the precision of the meter.

1(c)

  • Label the horizontal axis $d/\mathrm{cm}$ and the vertical axis $F_X/\mathrm{N}$. Start both at zero and choose scales so the points fill at least half the grid.
  • Plot each reading to within half a small square. Draw a thin, straight best-fit line through the trend of the points.

1(d)

  • Extend your best-fit line to $d = 0.0\,\mathrm{cm}$ and read the vertical intercept $F_0$.
  • Use $W_R = 2F_0$. For example, if $F_0 = 0.25\,\mathrm{N}$, then $W_R = 2(0.25\,\mathrm{N}) = \mathbf{0.50}\,\mathrm{N}$. Your result should be close to $W_X$.

1(e)

  • Compare your points with the line. If they lie close to a straight line, say yes: their clear pattern makes the line easy to choose.
  • If they are widely scattered, say no and refer to that scatter. Your statement must match your own graph.
Original question

Log in or create account

IGCSE, A-Level & AP