Skip to content

IGCSE Physics · June 2022 · Paper 53 · Difficulty 4 · Challenging

Question 1

1

In this experiment, you will investigate the forces supporting a metre rule.

Carry out the following instructions, referring to Fig. 1.1.

Do not attempt to change the position of either newton meter by adjusting the positions of the loops of thread attached to them.

Fig. 1.1
(a)

Move the $1.00\text{ N}$ load to a distance $d = 25.0\text{ cm}$ from the $0.0\text{ cm}$ end of the rule.

Move one stand slightly, if necessary, so that the newton meters are as near to vertical as possible.

Read, and record in Table 1.1, the value $F_\text{P}$ on newton meter P and the value $F_\text{Q}$ on newton meter Q.

Repeat this procedure for $d = 35.0\text{ cm}$, $d = 45.0\text{ cm}$, $d = 55.0\text{ cm}$ and $d = 65.0\text{ cm}$.

Table 1.1

$d/\text{cm}$$F_\text{P}/\text{N}$$F_\text{Q}/\text{N}$
25.0
35.0
45.0
55.0
65.0

[2]

(b)

Plot a graph of $F_\text{P}/\text{N}$ ($y$-axis) against $d/\text{cm}$ ($x$-axis).

On the same axes, and using the same scales, plot a graph of $F_\text{Q}/\text{N}$ ($y$-axis) against $d/\text{cm}$ ($x$-axis).

Draw two best-fit lines, one for each set of plots. Show clearly on your graph which line is for $F_\text{P}$ and which line is for $F_\text{Q}$.

[5]

(c)

From your graph, determine $F_0$, the value of $F_\text{P}$ where the two best-fit lines cross.

$F_0 =$

Calculate the weight $W_\text{R}$ of the metre rule, using the equation $W_\text{R} = (2 \times F_0) - k$, where $k = 1.00\text{ N}$.

$W_\text{R} =$ [2]

(d)

This experiment can be done by moving a clamp to make the rule horizontal before taking each reading.

Explain how to make sure that the rule is horizontal.

You may draw a diagram.[1]

(e)

A student does the experiment with the same equipment as you. He reads values of $F_\text{P}$ which are the same as yours but his values of $F_\text{Q}$ are all higher than yours by $0.10\text{ N}$.

Suggest a reason for this difference. Assume that your values of $F_\text{P}$ and $F_\text{Q}$ in Table 1.1 are correct.[1]

[Total: 11]

Show the mark scheme

These are the official mark-scheme rows. Each point that matches your answer earns a mark.

Tap the mark scheme to open it full size.

Show a worked answer

How to reach each mark, step by step. Try the question yourself first.

1(a)

  • Record both meter readings for each position, to at least one decimal place.
  • As the load moves towards Q, $F_P$ should decrease and $F_Q$ should increase. All readings should be below $3\,\mathrm{N}$.

1(b)

  • Label the horizontal axis $d/\mathrm{cm}$ and use the same vertical scale for $F_P/\mathrm{N}$ and $F_Q/\mathrm{N}$.
  • Choose scales so the plots cover at least three large squares in each direction. Plot each reading within half a small square.
  • Draw two thin best-fit lines and label them P and Q. They should cross at $d = 50.0\,\mathrm{cm}$, within one small square.

1(c)

  • Read $F_0$ from the vertical axis at the point where the lines cross. Use $W_R = 2F_0 - k$.
  • For example, if $F_0 = 1.50\,\mathrm{N}$, then $W_R = 2(1.50\,\mathrm{N}) - 1.00\,\mathrm{N} = \mathbf{2.00}\,\mathrm{N}$. Use your own graph reading.

1(d)

  • Measure the distance from the rule to the bench at two points. Adjust the clamp until the distances are equal, so the rule is horizontal.

1(e)

  • Newton meter Q may have a zero error: it may not have been set to zero before the experiment.
Original question

Log in or create account

IGCSE, A-Level & AP