Skip to content

IGCSE Physics · June 2022 · Paper 51 · Difficulty 3 · Standard

Question 1

1

In this experiment, you will investigate the stretching of a spring.

Carry out the following instructions, referring to Fig. 1.1.

Fig. 1.1
(a)

The metre rule is clamped in position close to the spring. Do not change the position of the metre rule.

(i)

Take two readings from the metre rule to determine the unstretched length $l_0$ of the coiled part of the spring. Use the set square provided.

reading 1 cm

reading 2 cm

$l_0$ = cm[3]

(ii)

Draw a diagram to show clearly how you used the set square to obtain an accurate reading from the metre rule.[1]

(b)

Suspend a load of $P = 1.0\text{N}$ from the spring.

Record the new length $l_1$ of the coiled part of the spring.

$l_1$ = cm

Calculate the extension $e_1$ using the equation $e_1 = (l_1 - l_0)$.

$e_1$ = cm

Calculate a value for the spring constant $k$ of the spring using the equation $k = \frac{P}{e_1}$.

Include the unit.

$k$ = [2]

(c)

Suspend a load of $P = 5.0\text{N}$ from the spring.

Record the new length $l_5$ of the coiled part of the spring.

$l_5$ = cm

Calculate the extension $e_5$ using the equation $e_5 = (l_5 - l_0)$.

$e_5$ = cm

Calculate a second value for the spring constant $k$ of the spring using the equation $k = \frac{P}{e_5}$.

Include the unit.

$k$ = [2]

(d)

State whether your two values of the spring constant $k$ can be considered equal within the limits of experimental accuracy.

Explain your answer by referring to your results.

statement

explanation

[1]

(e)

A student improves the experiment by taking additional sets of readings.

(i)

Suggest the additional apparatus that the student uses.

[1]

(ii)

Suggest how the student uses the additional results.

[1]

[Total: 11]

Show the mark scheme

These are the official mark-scheme rows. Each point that matches your answer earns a mark.

Tap the mark scheme to open it full size.

Show a worked answer

How to reach each mark, step by step. Try the question yourself first.

1(a)(i)

  • Use the set square to read the top and bottom of the coils. Record each reading to the nearest $0.1\,\mathrm{cm}$.
  • Use $l_0 = \text{bottom reading} - \text{top reading}$. For example, if the readings are $14.0\,\mathrm{cm}$ and $10.0\,\mathrm{cm}$, then $l_0 = 14.0\,\mathrm{cm} - 10.0\,\mathrm{cm} = \mathbf{4.0}\,\mathrm{cm}$.

1(a)(ii)

  • Place one edge of the set square level with an end of the spring and the other against the metre rule. Draw it in this position to show how the reading is taken.

1(b)

  • Measure $l_1$ with the load attached. Use $e_1 = l_1 - l_0$. For example, if $l_1 = 5.0\,\mathrm{cm}$ and $l_0 = 4.0\,\mathrm{cm}$, then $e_1 = \mathbf{1.0}\,\mathrm{cm}$.
  • Use $k = P/e_1$. For this example, $k = 1.0\,\mathrm{N}/1.0\,\mathrm{cm} = \mathbf{1.0}\,\mathrm{N/cm}$. Use your own readings for your answer.

1(c)

  • Measure $l_5$ with the $5.0\,\mathrm{N}$ load. Use $e_5 = l_5 - l_0$. For example, if $l_5 = 9.0\,\mathrm{cm}$ and $l_0 = 4.0\,\mathrm{cm}$, then $e_5 = \mathbf{5.0}\,\mathrm{cm}$.
  • Use $k = P/e_5$. For this example, $k = 5.0\,\mathrm{N}/5.0\,\mathrm{cm} = \mathbf{1.0}\,\mathrm{N/cm}$. Use your own readings for your answer.

1(d)

  • Compare your two values of $k$. They are equal within experimental accuracy if their difference is small enough to be explained by measurement uncertainty.
  • If the difference is larger than the uncertainty allows, say they are not equal within experimental accuracy. Refer to your two values in your explanation.

1(e)(i)

  • Use additional loads to stretch the spring by different amounts.

1(e)(ii)

  • Use the extra readings to plot a graph of load against extension.
Original question

Log in or create account

IGCSE, A-Level & AP