Skip to content

IGCSE Physics · June 2021 · Paper 63 · Difficulty 3 · Standard

Question 1

1

A student investigates the behaviour of a spring, and then uses the spring to determine the density of modelling clay.

The apparatus is shown in Fig. 1.1.

(a)

Describe two precautions that the student should take when measuring the length of the spring, to ensure an accurate reading. You may draw a diagram.[2]

(b)

The student measures the length $l_0$ of the spring without any load.

$l_0 = 2.3$ cm

A load of weight $W = 2.0$ N is suspended from the spring, as shown in Fig. 1.2.

(i)

On Fig. 1.2, measure the stretched length $l$ of the spring.

$l = ................................................$ cm[1]

(ii)

Calculate the extension $e$ of the spring for a load of weight $W = 2.0$ N.

Use the equation $e = (l - l_0)$.

$e = ................................................$ cm[1]

(c)

The 2.0 N load is removed from the spring.

A load U is made of modelling clay wrapped on a wire hanger. Load U is suspended from the spring.

The student measures the stretched length $l_U$ of the spring.

$l_U = 7.4$ cm

Calculate the extension $e_U$ of the spring with load U.

$e_U = ......................................................$ cm

The extension of a spring is directly proportional to the weight of the load.

Use your values of $W$ and $e$ from (b)(ii) and your value of $e_U$ to determine the weight $W_U$ of load U.

Show your working.

$W_U = ...........................................................$[2]

(d)

Load U is fully immersed in a beaker of water, as shown in Fig. 1.3.

On Fig. 1.3, measure the stretched length $l_W$ of the spring.

$l_W = ......................................................$ cm

Calculate the extension $e_W$ of the spring with load U in the water.

$e_W = ......................................................$ cm

Calculate the density $\rho$ of the modelling clay.

Use your values of $e_U$ from (c), your value of $e_W$ and the equation

$\rho = \frac{e_U}{(e_U - e_W)} \times k$, where $k = 1.0$ g/cm$^3$.

$\rho = ................................................$ g/cm$^3$[2]

(e)

Suggest a possible source of inaccuracy in the determination of $\rho$ in this experiment.[1]

(f)

The student plots a graph of load against extension for the spring, to show that the two quantities are directly proportional.

State how his graph line shows that load and extension are directly proportional.

[2]

Show the mark scheme

These are the official mark-scheme rows. Each point that matches your answer earns a mark.

Tap the mark scheme to open it full size.

Show a worked answer

How to reach each mark, step by step. Try the question yourself first.

1(a)

  • Place the rule close to and parallel to the spring.
  • Read the scale with your eye level with the end of the spring to avoid parallax.

1(b)(i)

  • Measure the stretched spring on the diagram: $l = \mathbf{10.7}\,\mathrm{cm}$.

1(b)(ii)

  • Use $e = l-l_0$.
  • $e = 10.7\,\mathrm{cm}-2.3\,\mathrm{cm} = \mathbf{8.4}\,\mathrm{cm}$.

1(c)

  • Use $e_U = l_U-l_0$: $e_U = 7.4\,\mathrm{cm}-2.3\,\mathrm{cm} = \mathbf{5.1}\,\mathrm{cm}$.
  • Write the weights as $F_W = W$ and $F_{W,U} = W_U$. Since weight is proportional to extension, $F_{W,U} = F_W e_U/e$.
  • $F_{W,U} = (2.0\,\mathrm{N})(5.1\,\mathrm{cm})/(8.4\,\mathrm{cm}) = \mathbf{1.2}\,\mathrm{N}$.

1(d)

  • Measure between the dashed lines: $l_W = \mathbf{3.9}\,\mathrm{cm}$.
  • Subtract the unloaded length: $e_W = l_W - l_0 = 3.9\,\mathrm{cm} - 2.3\,\mathrm{cm} = \mathbf{1.6}\,\mathrm{cm}$.
  • From (c), $e_U = l_U - l_0 = 7.4\,\mathrm{cm} - 2.3\,\mathrm{cm} = 5.1\,\mathrm{cm}$. Use $\rho = \dfrac{e_U}{e_U-e_W}\times k$.
  • $\rho = \dfrac{5.1\,\mathrm{cm}}{5.1\,\mathrm{cm}-1.6\,\mathrm{cm}}\times 1.0\,\mathrm{g/cm^3} = \mathbf{1.5}\,\mathrm{g/cm^3}$.

1(e)

  • Air bubbles attached to the immersed clay increase the upthrust and affect the result.

1(f)

  • The graph is a straight line through the origin.
Original question

Log in or create account

IGCSE, A-Level & AP