Skip to content

IGCSE Physics · June 2020 · Paper 53 · Difficulty 3 · Standard

Question 1

1

In this experiment, you will determine the weight of a metre rule. Carry out the following instructions, referring to Fig. 1.1.

Fig. 1.1
(a)
(i)

Ensure that the $10.0\text{ cm}$ mark on the metre rule is immediately above the pivot and that the metre rule is suspended from the forcemeter at the $90.0\text{ cm}$ mark. The metre rule should always be in this position before taking a reading.

Move the $200\text{ g}$ mass to a distance $l = 20.0\text{ cm}$ from the pivot as shown in Fig. 1.1.

Adjust the height of the clamp holding the pivot so that the metre rule is horizontal.

Read, and record in Table 1.1, the forcemeter reading $F$.

Repeat this procedure for values of $l = 30.0\text{ cm}$, $40.0\text{ cm}$, $50.0\text{ cm}$ and $60.0\text{ cm}$.

Table 1.1

$l / \text{cm}$$F / \text{N}$
20.0
30.0
40.0
50.0
60.0

[2]

(ii)

Explain how you made sure that the metre rule was horizontal before each reading was taken. You may draw a diagram.[1]

(b)

Plot a graph of $F/\text{N}$ ($y$-axis) against $l/\text{cm}$ ($x$-axis). Start your axes from the origin $(0,0)$.

[4]

(c)
(i)

From your graph determine $F_0$, the value of $F$ when $l = 0$.

$F_0 =$ [1]

(ii)

Calculate the weight $W_\text{R}$ of the metre rule, using the equation $W_\text{R} = 2 \times F_0$. Give $W_\text{R}$ to a suitable number of significant figures for this experiment.

$W_\text{R} =$ [2]

(d)

A student carrying out this experiment places the $200\text{ g}$ mass on the metre rule instead of hanging it from the loop of thread.

Suggest which of these is likely to be the more accurate method. Explain your answer by reference to the procedure.[1]

[Total: 11]

Show the mark scheme

These are the official mark-scheme rows. Each point that matches your answer earns a mark.

Tap the mark scheme to open it full size.

Show a worked answer

How to reach each mark, step by step. Try the question yourself first.

1(a)(i)

  • Record five measured forces in $\mathrm{N}$, one for each distance in the table. Give each reading to at least one decimal place.
  • The forces should increase as the mass moves farther from the pivot: a larger turning effect needs a larger upward force. Each reading should be below $5\,\mathrm{N}$.
  • There is no fixed numerical table: the readings depend on the apparatus. The diagram does not show a readable forcemeter scale.

1(a)(ii)

  • Measure the distance from the bench to the rule at each end. Adjust the rule until the two distances are equal.

1(b)

  • Label the horizontal axis $l / \mathrm{cm}$ and the vertical axis $F / \mathrm{N}$. Start both axes at zero.
  • Choose scales so the plotted points cover at least half the grid.
  • Plot each reading to within half a small square, then draw a thin, well-judged line of best fit.

1(c)(i)

  • Extend the straight line of best fit to $l = 0$. The force where it meets the vertical axis is $F_0$; read it in $\mathrm{N}$.
  • A numerical value needs your measured graph. Do not use zero unless the line actually passes through the origin.

1(c)(ii)

  • Use $W_R = 2F_0$, where $W_R$ is the metre rule’s weight in this paper.
  • Double your graph intercept: $W_R = \mathbf{2F_0}$. If $F_0$ is in $\mathrm{N}$, the answer is in $\mathrm{N}$. Give two or three significant figures.

1(d)

  • The loop of thread is more accurate: it can be placed at a precise mark, while the centre of the mass is harder to locate.
Original question

Log in or create account

IGCSE, A-Level & AP