Skip to content

IGCSE Physics · March 2022 · Paper 62 · Difficulty 3 · Standard

Question 1

1

A student investigates the extension of a spring and uses it to determine the weight of a metre rule.

The spring is shown full size in Fig. 1.1 and Fig. 1.2.

Fig. 1.1 shows the spring without any load.

Fig. 1.2 shows the spring with a load of 1.0N suspended from it.

(a)

On Fig. 1.1, measure the length $l_0$ of the spring without any load.

$l_0$ = cm

On Fig. 1.2, measure the stretched length $l_S$ of the spring.

$l_S$ = cm[2]

(b)

The student attaches a metre rule to the spring with a wire hook, as shown in Fig. 1.3. The scale of the metre rule faces upwards.

She ensures that the metre rule is horizontal.

Briefly describe how to check that the rule is horizontal. You may draw a diagram if it helps to explain your answer.

[1]

(c)

The student moves load W to distances $d = 20.0\text{ cm}$, $d = 30.0\text{ cm}$, $d = 40.0\text{ cm}$, $d = 50.0\text{ cm}$ and $d = 60.0\text{ cm}$ from the pivot.

She reads the length $l$ of the spring for each value of $d$.

Her readings are shown in Table 1.1.

d/cml/cm
20.06.2
30.07.1
40.07.6
50.08.3
60.09.0
(i)

Using the values from Table 1.1, plot a graph of $l/\text{cm}$ ($y$-axis) against $d/\text{cm}$ ($x$-axis).

Start the axes at the origin (0,0).

[4]

(ii)

From your graph, determine $L$, the value of $l$ when $d = 0.0\text{ cm}$.

$L$ = [1]

(iii)

Calculate $W_R$, the weight of the metre rule, using your value of $L$ from (c)(ii), the values of $l_0$ and $l_S$ from (a) and the equation

$$W_R = \frac{2(L - l_0)}{(l_S - l_0)} \times k$$

where $k = 1.0\text{ N}$.

$W_R$ = [1]

(d)
(i)

It is sometimes difficult to position the load W on the scale of the metre rule at the correct distance $d$ from the pivot.

Suggest one change to the apparatus to overcome this difficulty.

[1]

(ii)

Suggest one possible source of inaccuracy other than the difficulty described in (d)(i). Assume that the experiment is carried out carefully.

[1]

[Total: 11]

Show the mark scheme

These are the official mark-scheme rows. Each point that matches your answer earns a mark.

Tap the mark scheme to open it full size.

Show a worked answer

How to reach each mark, step by step. Try the question yourself first.

1(a)

  • Measure each spring from end to end. The readings are $l_0 = \mathbf{2.0}\,\mathrm{cm}$ and $l_S = \mathbf{6.2}\,\mathrm{cm}$.

1(b)

  • Measure the height of each end above the bench. The rule is horizontal when the heights are equal.

1(c)(i)

  • Label the horizontal axis $d/\mathrm{cm}$ and the vertical axis $l/\mathrm{cm}$. Start both at zero and choose scales that use at least half the grid.
  • Plot the five pairs from the table accurately. Draw a thin line of best fit and extend it to the vertical axis.

1(c)(ii)

  • Read the vertical intercept, where $d = 0\,\mathrm{cm}$. A best-fit line gives about $L = \mathbf{4.9}\,\mathrm{cm}$; your value depends on your line.

1(c)(iii)

  • Use $W_R = \frac{2(L-l_0)}{l_S-l_0}k$.
  • For $L = 4.9\,\mathrm{cm}$, $W_R = \frac{2(4.9-2.0)\,\mathrm{cm}}{(6.2-2.0)\,\mathrm{cm}}(1.0\,\mathrm{N}) = \mathbf{1.4}\,\mathrm{N}$.

1(d)(i)

  • Hang the load from a thin loop of thread around the rule. Place the thread on the required mark so the load does not hide the scale.

1(d)(ii)

  • The metre rule may be non-uniform, so its centre of mass may not be at its midpoint.
Original question

Log in or create account

IGCSE, A-Level & AP