Skip to content

IGCSE Physics · March 2021 · Paper 52 · Difficulty 4 · Challenging

Question 3

3

In this experiment, you will investigate a resistor and a lamp connected in series. The circuit has been set up for you with the voltmeter connected to measure the potential difference across the lamp.

Carry out the following instructions, referring to Fig. 3.1.

(a)
(i)

Switch on.

Move the crocodile clip on the resistance wire so that the value of the potential difference $V_L$ across the lamp is 2.0V.

Measure, and record in Table 3.1, the value of the current $I$ for the lamp and resistor in series.

Disconnect the voltmeter and re-connect it so that it measures the potential difference across the resistor.

Measure, and record in Table 3.1, the value of the potential difference $V_R$ across the resistor.

Switch off.

Disconnect the voltmeter and re-connect it in its original position across the lamp.[1]

(ii)

Repeat the steps in (a)(i) for $V_L = 1.0V$ and $V_L = 0.5V$.[2]

Table 3.1

$V_L/V$$I / A$$V_R /V$$R_L/\Omega$$R_R / \Omega$
2.0
1.0
0.5
(b)

Calculate, and record in Table 3.1, the resistance of the lamp $R_L$ for each value of $V_L$.

Use your values of $V_L$ and $I$ from Table 3.1 and the equation $R_L = \frac{V_L}{I}$.

Calculate, and record in Table 3.1, the resistance of the resistor $R_R$ for each value of $V_L$.

Use your values of $V_R$ and $I$ from Table 3.1 and the equation $R_R = \frac{V_R}{I}$.[3]

(c)

A student suggests that $R_R$ should be constant.

State whether your results support this suggestion.

Justify your statement by reference to values from Table 3.1.[2]

(d)

A student wishes to determine the resistance of the lamp $R_L$ when the potential difference across the lamp $V_L = 0.0V$.

Describe how the experiment can be extended to do this with the help of a suitable graph. You are not required to carry out this additional experiment.[2]

(e)

It is possible to use a variable resistor instead of a resistance wire to change the potential difference across the lamp.

Complete the circuit in Fig. 3.2 to show a variable resistor used for this purpose.

You are not required to carry out this experiment.

[1]

[Total: 11]

Show the mark scheme

These are the official mark-scheme rows. Each point that matches your answer earns a mark.

Tap the mark scheme to open it full size.

Show a worked answer

How to reach each mark, step by step. Try the question yourself first.

3(a)(i)

  • Set $V_L$ to $2.0\,\mathrm{V}$. Record the current and then move the voltmeter across the resistor to record $V_R$.
  • The current should be below $1.00\,\mathrm{A}$. Its exact value depends on your circuit.

3(a)(ii)

  • Repeat the measurements at $1.0\,\mathrm{V}$ and $0.5\,\mathrm{V}$. Record $I$ to at least two decimal places and $V_R$ to at least one decimal place.
  • As $V_L$ falls, both $I$ and $V_R$ should fall. Each $V_R$ reading should be below $1.0\,\mathrm{V}$.

3(b)

  • Use $\mathbf{R_L = V_L/I}$ and $\mathbf{R_R = V_R/I}$ for each row. Divide each voltage in $\mathrm{V}$ by that row’s current in $\mathrm{A}$ to obtain resistance in $\mathrm{\Omega}$.
  • Record all resistances to two significant figures or all to three significant figures.
  • As $V_L$ decreases, $R_L$ should decrease. The three $R_R$ values should be within $10\%$ of each other.

3(c)

  • Compare the three $R_R$ values in your table and quote them in $\mathrm{\Omega}$.
  • If they are close within experimental uncertainty, they support a constant resistance. If they differ by more than the uncertainty, they do not support it.

3(d)

  • Take more readings at different lamp voltages, calculate $R_L$ for each, and plot $R_L$ against $V_L$.
  • Extend the line to the $R_L$ axis. The intercept gives $R_L$ at $V_L = 0\,\mathrm{V}$.

3(e)

  • Add a variable resistor in series with the lamp and ammeter. Its symbol is a rectangle with a diagonal arrow through it.
Original question

Log in or create account

IGCSE, A-Level & AP