原始开放焦点复习;完整规格覆盖仍不完整。
1 · 面向真实用户进行设计
ergonomics · specification
ib_design_technology_hl:design_users:open:1 · 2 分
哪一项是可验证的要求?
- 手柄必须美观
- 手柄必须承受规定的100 N监管测试载荷
- 设计师必须喜欢它
答案与解析
手柄必须承受规定的100 N监管测试载荷
- Choose data for the target population and task. Clearance often needs a larger-user percentile; reach may need a smaller-user percentile. A single mean dimension cannot satisfy every design constraint.
ib_design_technology_hl:design_users:open:2 · 4 分
使用力为30 N,选定安全系数为3。求目标载荷。
答案与解析
90 N
- Appropriate relation; consistent substitution; correct result; meaningful unit and interpretation.
规格说明书不应是诸如“美观”或“坚固”等模糊愿望的清单。用户测试应评估可衡量的需求并揭示相互冲突的要求。
2 · 人体工程学:适应一系列用户。
anthropometry · ergonomics
ib_design_technology_hl:design_ergonomics:open:1 · 2 分
当某个固定控件对于部分预期用户无法触及时,哪项决策最具可辩护性?
- 针对指定的用户范围测试较近或可调节的位置
- 仅使用最大的测量可达距离
- 假设平均值保证访问
答案与解析
针对指定的用户范围测试较近或可调节的位置。
- A clearance dimension often needs to consider larger relevant body dimensions, while reach can require smaller relevant dimensions. Neither principle automatically selects a universal percentile. The measured population, posture, clothing, capability and task determine relevance. Consider physical, perceptual and cognitive demands together rather than assuming body size explains every usability issue.
ib_design_technology_hl:design_ergonomics:open:2 · 4 分
在指定的最近秩方法中,使用公式 ceil(p×n)。当 p=0.90 且 n=20 时,求其秩。
答案与解析
18 等级
- Appropriate relation; consistent substitution; correct result; meaningful unit and interpretation.
百分位数的计算方法各不相同,尤其是针对小样本时。百分位数并非身体尺寸的百分比。平均尺寸以及单个用户的成功测试并不能确立无障碍设计。
3 · 模型、材料及迭代原型制作
prototype · iteration
ib_design_technology_hl:design_models:open:1 · 2 分
比例外观模型能直接确立什么?
- 全尺寸疲劳强度
- 其所代表的布局与形态
- 全部生产成本
答案与解析
其所代表的布局与形态
- State what each model includes and omits. Compare tests with the same load, geometry and conditions. Iteration means using evidence to revise a solution and testing the revision against the original success criteria.
ib_design_technology_hl:design_models:open:2 · 4 分
在同等条件下,挠度从10 mm降至6 mm。求百分比减少量。
答案与解析
40 %
- Appropriate relation; consistent substitution; correct result; meaningful unit and interpretation.
刚度是抵抗弹性变形的能力;强度涉及失效应力。外观逼真的模型不一定能再现材料行为。
4 · 制造:公差、变异和检验。
tolerance · clearance
ib_design_technology_hl:design_tolerances:open:1 · 2 分
哪些尺寸决定了最小最坏情况间隙?
- 最小孔径减去最大轴径
- 最大孔径减去最小轴径
- 标称孔径加标称轴径
答案与解析
最小孔径减去最大轴径。
- For a worst-case clearance model, subtract the largest shaft from the smallest hole for minimum clearance, and the smallest shaft from the largest hole for maximum clearance. The calculation assumes the stated dimensional limits and ideal geometry. Shape, alignment, temperature and measurement uncertainty can affect actual assembly.
ib_design_technology_hl:design_tolerances:open:2 · 4 分
孔径范围为 12.0 至 12.4 毫米,轴径为 11.5 至 11.8 毫米。计算最小间隙。
答案与解析
0.2 毫米
- Appropriate relation; consistent substitution; correct result; meaningful unit and interpretation.
更严格的公差可能会增加成本、检验时间和废料,且未必能改善用户体验。显示精细的测量仪器并不自动具备接受极限附近零件所需的准确度。
5 · 设计可持续性与生产选择
design for disassembly · tolerance
ib_design_technology_hl:design_lifecycle:open:1 · 2 分
哪一项支持可维修性?
- 所有部件永久粘接
- 易于更换的可替换磨损件
- 无计划地隐藏所有紧固件
答案与解析
易于更换的可替换磨损件
- Compare a common service over a stated lifetime. Separate fixed tooling cost from cost per item. Include repair, energy, transport and realistic end-of-life pathways rather than using a recycled label as the whole judgement.
ib_design_technology_hl:design_lifecycle:open:2 · 4 分
固定成本相差400单位,单位成本相差5。求盈亏平衡数量。
答案与解析
80 件
- Appropriate relation; consistent substitution; correct result; meaningful unit and interpretation.
更便宜的生产工艺并非自动优选。成本估算需要明确货币、数量和假设,且原型不能证明大规模生产的一致性。